kann nach k3b Tutorial immer noch nicht brennen

Cinderella

Active Member
Ich habe das k3b Tutorial aus dem wiki durchgearbeitet und kann nun auch als User k3b benutzen, nur cdrecord macht Ärger. Ich kann weder cdr noch dvdrs brennen. Ich hab hier mal das komplette Protokoll kopiert. Ich seh da um ehrlich zu seien nicht durch.

Der Brenner ist ein LG GSA-4160B. Also wenn einer ne Idee oder einen Link und selber einen LG Brenner hat, wäre ich für nen Hinweis dankbar.

CU
Cinderella




Devices
-----------------------
HL-DT-ST DVDRAM GSA-4160B A300 (/dev/cd0, ) at /lg [CD-R; CD-RW; CD-ROM; DVD-ROM; DVD-R; DVD-RW; DVD+R; DVD+RW] [DVD-ROM; DVD-R Sequential; DVD-RAM; DVD-RW Restricted Overwrite; DVD-RW Sequential; DVD+RW; DVD+R; DVD+R Double Layer; CD-ROM; CD-R; CD-RW] [SAO; TAO; RAW]
TOSHIBA DVD-ROM SD-M1612 1004 (/dev/cd1, ) at /toshiba [CD-ROM; DVD-ROM] [DVD-ROM; CD-ROM] [None]

System
-----------------------
K3b Version: 0.11.20
KDE Version: 3.3.0
QT Version: 3.3.3
Kernel: 5.3-RELEASE

cdrecord
-----------------------
scsidev: '1,0,0'
scsibus: 1 target: 0 lun: 0
SCSI buffer size: 64512
/usr/local/bin/cdrecord: This version of cdrecord does not include DVD-R/DVD-RW support code.
/usr/local/bin/cdrecord: If you need DVD-R/DVD-RW support, ask the Author for cdrecord-ProDVD.
/usr/local/bin/cdrecord: Free test versions and free keys for personal use are at ftp://ftp.berlios.de/pub/cdrecord/ProDVD/
/usr/local/bin/cdrecord: Input/output error. read buffer: scsi sendcmd: retryable error
CDB: 3C 00 00 00 00 00 00 FC 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 04 00 00 00 00 10 9E 68 85 80 08 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Sense Key: 0x4 Hardware Error, Segment 0
Sense Code: 0x08 Qual 0x03 (logical unit communication crc error (ultra-dma/32)) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.003s timeout 40s
Cdrecord-Clone 2.01 (i386-unknown-freebsd5.3) Copyright (C) 1995-2004 Jörg Schilling
TOC Type: 1 = CD-ROM
Using libscg version 'schily-0.8'.
Driveropts: 'burnfree'
atapi: 0
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : 'HL-DT-ST'
Identifikation : 'DVDRAM GSA-4160B'
Revision : 'A300'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0009
Profile: 0x0012
Profile: 0x0011
Profile: 0x0014
Profile: 0x0013
Profile: 0x001A
Profile: 0x001B
Profile: 0x002B
Profile: 0x0010
Profile: 0x0009 (current)
Profile: 0x000A
Profile: 0x0008
Profile: 0x0002
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1053696 = 1029 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 440 MB
Total size: 505 MB (50:05.00) = 225375 sectors
Lout start: 505 MB (50:07/00) = 225375 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 5
Is not unrestricted
Is not erasable
Disk sub type: Medium Type B, low Beta category (B-) (4)
ATIP start of lead in: -11834 (97:24/16)
ATIP start of lead out: 359849 (79:59/74)
Disk type: Short strategy type (Phthalocyanine or similar)
Manuf. index: 24
Manufacturer: SONY Corporation
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 134474
Starting to write CD/DVD at speed 8 in dummy TAO mode for single session.
Last chance to quit, starting dummy write in 2 seconds.
1 seconds.
0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is ON.
Starting new track at sector: 0
Track 01: 0 of 440 MB written.
/usr/local/bin/cdrecord: Input/output error. write_g1: scsi sendcmd: retryable error
CDB: 2A 00 00 00 00 1F 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 04 00 00 00 00 10 9B F8 2B 80 08 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Sense Key: 0x4 Hardware Error, Segment 0
Sense Code: 0x08 Qual 0x03 (logical unit communication crc error (ultra-dma/32)) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.003s timeout 40s
/usr/local/bin/cdrecord: A write error occured.
/usr/local/bin/cdrecord: Please properly read the error message above.
write track data: error after 63488 bytes
Writing time: 11.121s
Average write speed 271.2x.
Fixating...
WARNING: Some drives don't like fixation in dummy mode.
Fixating time: 34.038s
/usr/local/bin/cdrecord: fifo had 65 puts and 2 gets.
/usr/local/bin/cdrecord: fifo was 0 times empty and 1 times full, min fill was 98%.

cdrecord comand:
-----------------------
/usr/local/bin/cdrecord -v gracetime=2 dev=1,0,0 speed=8 -tao -dummy driveropts=burnfree -data /usr/burnbuffer/k3b_1.iso
 
Hab den DMA Modus für die ATAPI Laufwerke deaktiviert und dann gings:

in /boot/loader.conf

hw.ata.atapi_dma=0

eintragen.

CU
Cinderella
 
Back
Top