Kein sound mit snd_hda.ko

cabriofahrer

Well-Known Member
Seit den letzten Releases von FreeBSD bekomme ich auf meinem Notebook mittels kldload snd_hda.ko keinen Sound mehr. Mit FreeBSD 7.0 ? (oder 6.3?) klappte das noch problemlos.
Ich weiß, daß die Lösung wahrscheinlich irgendwo in man snd_hda oder man sound zu finden ist, doch werde ich nicht schlau daraus...
 
Ja. Wie gesagt, ich vermute, daß man da was mit sysctl machen muß. Aber aus den Manpages werde ich eben nicht schlau...
 
Sicher, dass er auf die korrekten Ausgänge routet? Da snd_hda.ko nun vollständig standardkonform ist, hat sich die Ausgangseinteilung unter Umständen geändert. Einfach mal in die Manpage schauen, da wird es alles erklärt.
 
Und du kannst die Soundkarte auch in Programmen auswählen und diese meckern nicht?

Ansonsten wäre wohl die Info aus dmesg für die Soundkarte interessant.
 
Deine verschiedenen Ausgänge werden jetzt als separate Soundkarten angeboten. Du musst nur mit einem sysctl den Richtigen Standard-dsp setzen.

Manpage snd(4) lesen, da steht's drin.
 
Deine verschiedenen Ausgänge werden jetzt als separate Soundkarten angeboten. Du musst nur mit einem sysctl den Richtigen Standard-dsp setzen.

Manpage snd(4) lesen, da steht's drin.

Hmm, sehr praktisch das! Damit könnte man also ne ordentliche aktive Frequenzweiche fahren...
 
Danke für Deinen Einwand, Marky. Genau so ist es nämlich. Und hier alles, was ich ausgeben kann:

# kldload -v snd_hda.ko
Loaded snd_hda.ko, id=12

Code:
# dmesg 
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.2-RELEASE #0: Fri May  1 08:49:13 UTC 2009
    root@walker.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) M processor 1.60GHz (1596.01-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6d8  Stepping = 8
  Features=0xafe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE>
  Features2=0x180<EST,TM2>
  AMD Features=0x100000<NX>
real memory  = 1072168960 (1022 MB)
avail memory = 1035497472 (987 MB)
ACPI APIC Table: <INTEL  ALVISO  >
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <PTLTD   RSDT> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
unknown: I/O range not supported
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x1d> port 0x62,0x66 on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0-0x3ff on acpi0
device_attach: acpi_hpet0 attach returned 12
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0x2000-0x20ff mem 0xd0000000-0xd7ffffff,0xc8100000-0xc810ffff irq 16 at device 0.0 on pci1
pci0: <multimedia, HDA> at device 27.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
pci9: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0
pci10: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
pci2: <ACPI PCI bus> on pcib4
uhci0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> port 0x1800-0x181f irq 23 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> port 0x1820-0x183f irq 19 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
uhci1: [ITHREAD]
usb1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> port 0x1840-0x185f irq 18 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
uhci2: [ITHREAD]
usb2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> port 0x1860-0x187f irq 16 at device 29.3 on pci0
uhci3: [GIANT-LOCKED]
uhci3: [ITHREAD]
usb3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
uhub3: 2 ports with 2 removable, self powered
ehci0: <Intel 82801FB (ICH6) USB 2.0 controller> mem 0xc8004000-0xc80043ff irq 23 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <Intel 82801FB (ICH6) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb4
uhub4: 8 ports with 8 removable, self powered
umass0: <Cypress Semiconductor USB2.0 Storage Device, class 0/0, rev 2.00/0.01, addr 2> on uhub4
umass0: Get Max Lun not supported (STALLED)
pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci6: <ACPI PCI bus> on pcib5
pci6: <network> at device 3.0 (no driver attached)
bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x3003> mem 0xc8200000-0xc820ffff irq 16 at device 6.0 on pci6
miibus0: <MII bus> on bge0
brgphy0: <BCM5705 10/100/1000baseTX PHY> PHY 1 on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge0: Ethernet address: 00:c0:9f:7f:70:4c
bge0: [ITHREAD]
fwohci0: <Texas Instruments TSB43AB21/A/AI/A-EP> mem 0xc8215000-0xc82157ff,0xc8210000-0xc8213fff irq 19 at device 7.0 on pci6
fwohci0: [FILTER]
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:c0:9f:00:00:3f:9e:23
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:c0:9f:3f:9e:23
fwe0: Ethernet address: 02:c0:9f:3f:9e:23
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:c0:9f:00:00:3f:9e:23 @ 0xfffe00000000, S400, maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x1074000
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
cbb0: <O2Micro OZ711M3 PCI-CardBus Bridge> mem 0xc8216000-0xc8216fff irq 18 at device 9.0 on pci6
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb0: [ITHREAD]
cbb1: <O2Micro OZ711M3 PCI-CardBus Bridge> mem 0xc8217000-0xc8217fff irq 18 at device 9.1 on pci6
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
cbb1: [ITHREAD]
pci6: <base peripheral> at device 9.2 (no driver attached)
cbb2: <O2Micro OZ711M3 PCI-CardBus Bridge> at device 9.3 on pci6
cardbus2: <CardBus bus> on cbb2
pccard2: <16-bit PCCard bus> on cbb2
cbb2: [ITHREAD]
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH6M SATA150 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x18a0-0x18af at device 31.2 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
battery1: <ACPI Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model Generic PS/2 mouse, device ID 0
sio0 port 0x2f8-0x2ff irq 3 drq 1 flags 0x10 on acpi0
sio0: type 16550A
sio0: [FILTER]
cpu0: <ACPI CPU> on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
acpi_hpet0: <High Precision Event Timer> iomem 0-0x3ff on acpi0
device_attach: acpi_hpet0 attach returned 12
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xce800-0xcffff,0xe0000-0xe17ff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ums0: <RAPTOR-GAMING RAPTOR-GAMING LM1, class 0/0, rev 1.10/51.04, addr 2> on uhub3
ums0: 5 buttons and Z dir.
Timecounter "TSC" frequency 1596009908 Hz quality 800
Timecounters tick every 1.000 msec
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ad0: 76319MB <IC25N080ATMR04 0 MO4OAD4A> at ata0-master SATA150
pccard2: <unknown card> (manufacturer=0xffff, product=0x0001, function_type=-1) at function 0
pccard2:    CIS info: O2Micro, SmartCardBus Reader, V1.0
acd0: DVDR <PIONEER DVD-RW DVRKD08RS/1.02> at ata1-master UDMA33
cpu0: Cx states changed
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x48 0x00 0x01
(probe8:ata1:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe8:ata1:0:0:0): CAM Status: SCSI Status Error
(probe8:ata1:0:0:0): SCSI Status: Check Condition
(probe8:ata1:0:0:0): NOT READY asc:3a,0
(probe8:ata1:0:0:0): Medium not present
(probe8:ata1:0:0:0): Unretryable error
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <Maxtor 5 2049U4 \\0000\\0000> Fixed Direct Access SCSI-0 device 
da0: 40.000MB/s transfers
da0: 19541MB (40020624 512 byte sectors: 255H 63S/T 2491C)
cd0 at ata1 bus 0 target 0 lun 0
cd0: <PIONEER DVD-RW DVRKD08RS 1.02> Removable CD-ROM SCSI-0 device 
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
GEOM_LABEL: Label for provider da0s1a is ufsid/4aa4f7c739465bf6.
GEOM_LABEL: Label for provider da0s1d is ufsid/4aa4f7ca85600a8b.
GEOM_LABEL: Label for provider da0s1e is ufsid/4aa4f7c79a75413d.
GEOM_LABEL: Label for provider da0s1f is ufsid/4aa4f7c82d48a87b.
Trying to mount root from ufs:/dev/da0s1a
GEOM_LABEL: Label ufsid/4aa4f7c739465bf6 removed.
GEOM_LABEL: Label for provider da0s1a is ufsid/4aa4f7c739465bf6.
GEOM_LABEL: Label ufsid/4aa4f7c79a75413d removed.
GEOM_LABEL: Label for provider da0s1e is ufsid/4aa4f7c79a75413d.
GEOM_LABEL: Label ufsid/4aa4f7c82d48a87b removed.
GEOM_LABEL: Label for provider da0s1f is ufsid/4aa4f7c82d48a87b.
GEOM_LABEL: Label ufsid/4aa4f7ca85600a8b removed.
GEOM_LABEL: Label for provider da0s1d is ufsid/4aa4f7ca85600a8b.
GEOM_LABEL: Label ufsid/4aa4f7c739465bf6 removed.
GEOM_LABEL: Label ufsid/4aa4f7c79a75413d removed.
GEOM_LABEL: Label ufsid/4aa4f7c82d48a87b removed.
GEOM_LABEL: Label ufsid/4aa4f7ca85600a8b removed.
drm0: <ATI Radeon Mobility X700 M26> on vgapci0
vgapci0: child drm0 requested pci_enable_busmaster
info: [drm] Initialized radeon 1.29.0 20080528
info: [drm] Setting GART location based on new memory map
info: [drm] Loading R400 Microcode
info: [drm] Num pipes: 2
info: [drm] writeback test succeeded in 1 usecs
drm0: [ITHREAD]
pid 1267 (nepomukservicestub), uid 1001: exited on signal 11 (core dumped)
WARNING: attempt to net_add_domain(netgraph) after domainfinalize()
bge0: link state changed to DOWN
bge0: link state changed to UP
hdac0: <Intel 82801F High Definition Audio Controller> mem 0xc8000000-0xc8003fff irq 16 at device 27.0 on pci0
hdac0: HDA Driver Revision: 20090329_0131
hdac0: [ITHREAD]
hdac0: HDA Codec #0: Realtek ALC880
hdac0: HDA Codec #1: Lucent/Agere Systems (Unknown)

# ls /dev/mixer*
ls: No match.

ls /dev/dsp*
ls: No match.

# cat /dev/sndstat
FreeBSD Audio Driver (newpcm: 32bit 2007061600/i386)
Installed devices:

# sysctl hw.snd.default_unit
hw.snd.default_unit: -1

Wenn ich versuche:

# sysctl hw.snd.default_unit=0
hw.snd.default_unit: -1
sysctl: hw.snd.default_unit: Invalid argument


Ich hoffe, das hilft Euch weiter.
 
Hmm... Vielleicht wird die Karte auch nicht mehr (warum auch immer...) unterstützt?

Vielleicht mal oss ausprobieren?
 
Das wäre dann ja eine Regression, die man schnellstens melden sollte.
 
Zur Sicherheit führe erst mal folgenden Befehl aus:
# devfs rule apply path 'dsp*' unhide

Danach kannst du noch mal ls /dev/dsp* aufrufen.

Ich erinnere mich, dass irgendwo im 7.x Zweig die Dinger unsichtbar waren.
 
Die sind auch weiterhin unsichtbar. Das ist das Funktionsprinzip von "Device Cloning". Programm A öffnet /dev/dsp. Wollte nun Programm B öffnen, ginge das nicht. Daher klont man A transparent auf /dev/dsp0.1, B auf /dev/dsp0.2 und soweiter. Dabei sind die ungeklonten Geräte nur von dem Programm sichtbar, was sie gerade anfasst.

Ein Beispiel:
Code:
yamagi@screw:ttyp3 ~/temp: ls /dev          [16:14:57]
acpi       audit      fd         net        ptyp7      ttyp6      ttyva
ad0        cd0        fd0        net1       ptyp8      ttyp7      ttyvb
ad0s1      console    fido       net2       ptyp9      ttyp8      ttyvc
ad0s1a     consolectl fw0        net3       ptypa      ttyp9      ttyvd
ad0s1b     cpu0       fw0.0      net4       ptypb      ttypa      ttyve
ad0s1d     cpu1       fwmem0     net5       random     ttypb      ttyvf
ad0s1e     cpu2       fwmem0.0   network    sg0        ttyu0      ufs
ad0s1f     cpu3       geom.ctl   nfs4       sga        ttyu0.init ufsid
ad0s1g     ctty       io         nfslock    sndstat    ttyu0.lock ums0
ad0s1g.eli cuau0      kbd0       null       stderr     ttyv0      urandom
ad1        cuau0.init kbd1       pass0      stdin      ttyv1      usb
ad1p1      cuau0.lock kbdmux0    pci        stdout     ttyv2      usb0
ad1p1.eli  devctl     klog       ptyp0      sysmouse   ttyv3      usb1
ad2        devstat    kmem       ptyp1      ttyp0      ttyv4      vboxnetctl
ad2s1      dri        log        ptyp2      ttyp1      ttyv5      xpt0
ad2s1a     dsp1.0     mem        ptyp3      ttyp2      ttyv6      zero
ad2s1a.eli dsp1.1     midistat   ptyp4      ttyp3      ttyv7
ata        dsp1.2     mixer0     ptyp5      ttyp4      ttyv8
atkbd0     dumpdev    mixer1     ptyp6      ttyp5      ttyv9

Aber:
Code:
yamagi@screw:ttyp9 ~/temp: ls /dev/dsp                              [16:16:02]
/dev/dsp
 
Ich dachte es wird immer schon eins bereit gehalten, so dass man dann jeweils sehen kann wie viele Ausgänge ansteuerbar sind.

Aber mal zurück zum Thema, ich denke das hw.snd.default_unit nicht auf einem Wert >= 0 steht ist ein Zeichen für ein echtes Problem.

Die /dev/sndstat macht auch keine Hoffnung.

Hast du mal ein kld_load snd_driver ausprobiert.

Zugegeben eine verzweifelte Maßnahme. Aber vielleicht lädt das Modul einfach irgendwelche Abhängigkeiten nicht nach.
 
Könntest du vllt mal mit verbose logging booten und davon ein dmesg zeigen? Ich glaube das ist 5 beim starten, oder boot -v. Dann solltest du einen ganzen "Baum" an Informtaionen von hda erhalten. Vllt lässt sich so dem Problem auf die Schliche kommen.
 
Hier ein Teil der dmesg (mehr bekomme ich nicht) nach verbose logging und kldload snd_driver.ko:

Code:
pci6: driver added
found->	vendor=0x8086, dev=0x4223, revid=0x05
	domain=0, bus=6, slot=3, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0012, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D3  current D0
pci0:6:3:0: reprobing on driver added
found->	vendor=0x1217, dev=0x7110, revid=0x00
	domain=0, bus=6, slot=9, func=2
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0003, statreg=0x0410, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0:6:9:2: reprobing on driver added
pci9: driver added
pci10: driver added
acpi_hpet0: <High Precision Event Timer> iomem 0-0x3ff on acpi0
device_attach: acpi_hpet0 attach returned 12
sio4: irq maps: 0xc01 0xc01 0xc01 0xc01
sio4: probe failed test(s): 1 4 6 9
ppc0: using extended I/O port range
ppc0: using extended I/O port range
acpi_hpet0: <High Precision Event Timer> iomem 0-0x3ff on acpi0
device_attach: acpi_hpet0 attach returned 12
sio4: irq maps: 0xc01 0xc01 0xc01 0xc01
sio4: probe failed test(s): 1 4 6 9
ppc0: using extended I/O port range
pci0: driver added
found->	vendor=0x8086, dev=0x2668, revid=0x04
	domain=0, bus=0, slot=27, func=0
	class=04-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0010, cachelnsz=8 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=16
	powerspec 2  supports D0 D3  current D0
	MSI supports 1 message, 64 bit
pci0:0:27:0: reprobing on driver added
found->	vendor=0x8086, dev=0x266a, revid=0x04
	domain=0, bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=19
pci0:0:31:3: reprobing on driver added
pci1: driver added
pci2: driver added
pci6: driver added
found->	vendor=0x8086, dev=0x4223, revid=0x05
	domain=0, bus=6, slot=3, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0012, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D3  current D0
pci0:6:3:0: reprobing on driver added
found->	vendor=0x1217, dev=0x7110, revid=0x00
	domain=0, bus=6, slot=9, func=2
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0003, statreg=0x0410, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0:6:9:2: reprobing on driver added
pci9: driver added
pci10: driver added
pci0: driver added
found->	vendor=0x8086, dev=0x2668, revid=0x04
	domain=0, bus=0, slot=27, func=0
	class=04-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0010, cachelnsz=8 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=16
	powerspec 2  supports D0 D3  current D0
	MSI supports 1 message, 64 bit
pci0:0:27:0: reprobing on driver added
found->	vendor=0x8086, dev=0x266a, revid=0x04
	domain=0, bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=19
pci0:0:31:3: reprobing on driver added
pci1: driver added
pci2: driver added
pci6: driver added
found->	vendor=0x8086, dev=0x4223, revid=0x05
	domain=0, bus=6, slot=3, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0012, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D3  current D0
pci0:6:3:0: reprobing on driver added
found->	vendor=0x1217, dev=0x7110, revid=0x00
	domain=0, bus=6, slot=9, func=2
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0003, statreg=0x0410, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0:6:9:2: reprobing on driver added
pci9: driver added
pci10: driver added
pci0: driver added
found->	vendor=0x8086, dev=0x2668, revid=0x04
	domain=0, bus=0, slot=27, func=0
	class=04-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0010, cachelnsz=8 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=16
	powerspec 2  supports D0 D3  current D0
	MSI supports 1 message, 64 bit
pci0:0:27:0: reprobing on driver added
found->	vendor=0x8086, dev=0x266a, revid=0x04
	domain=0, bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=19
pci0:0:31:3: reprobing on driver added
pci1: driver added
pci2: driver added
pci6: driver added
found->	vendor=0x8086, dev=0x4223, revid=0x05
	domain=0, bus=6, slot=3, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0012, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D3  current D0
pci0:6:3:0: reprobing on driver added
found->	vendor=0x1217, dev=0x7110, revid=0x00
	domain=0, bus=6, slot=9, func=2
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0003, statreg=0x0410, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0:6:9:2: reprobing on driver added
pci9: driver added
pci10: driver added
pci0: driver added
found->	vendor=0x8086, dev=0x2668, revid=0x04
	domain=0, bus=0, slot=27, func=0
	class=04-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0010, cachelnsz=8 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=16
	powerspec 2  supports D0 D3  current D0
	MSI supports 1 message, 64 bit
pci0:0:27:0: reprobing on driver added
hdac0: <Intel 82801F High Definition Audio Controller> mem 0xc8000000-0xc8003fff irq 16 at device 27.0 on pci0
hdac0: HDA Driver Revision: 20090329_0131
hdac0: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xc8000000
hdac0: [MPSAFE]
hdac0: [ITHREAD]
hdac0: Probing codec #0...
hdac0: HDA Codec #0: Realtek ALC880
hdac0:  HDA Codec ID: 0x10ec0880
hdac0:        Vendor: 0x10ec
hdac0:        Device: 0x0880
hdac0:      Revision: 0x05
hdac0:      Stepping: 0x00
hdac0: PCI Subvendor: 0x00701025
hdac0: 	Found audio FG nid=1 startnode=2 endnode=34 total=32
hdac0: Probing codec #1...
hdac0: HDA Codec #1: Lucent/Agere Systems (Unknown)
hdac0:  HDA Codec ID: 0x11c13026
hdac0:        Vendor: 0x11c1
hdac0:        Device: 0x3026
hdac0:      Revision: 0x05
hdac0:      Stepping: 0x00
hdac0: PCI Subvendor: 0x00701025
hdac0: 	Found modem FG nid=1 startnode=2 endnode=40 total=38
hdac0: 
hdac0: Processing audio FG cad=0 nid=1...
hdac0: GPIO: 0x40000002 NumGPIO=2 NumGPO=0 NumGPI=0 GPIWake=0 GPIUnsol=1
hdac0:  nid 20 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0
hdac0:  nid 21 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0
hdac0:  nid 22 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0
hdac0:  nid 23 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0
hdac0:  nid 24 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0
hdac0:  nid 25 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0
hdac0:  nid 26 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0
hdac0:  nid 27 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0
hdac0:  nid 28 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0
hdac0: Patching widget caps nid=29 0x00400000 -> 0x00700000
hdac0:  nid 30 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0
hdac0:  nid 31 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0
hdac0: Patched pins configuration:
hdac0:  nid 20 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0 [DISABLED]
hdac0:  nid 21 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0 [DISABLED]
hdac0:  nid 22 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0 [DISABLED]
hdac0:  nid 23 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0 [DISABLED]
hdac0:  nid 24 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0 [DISABLED]
hdac0:  nid 25 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0 [DISABLED]
hdac0:  nid 26 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0 [DISABLED]
hdac0:  nid 27 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0 [DISABLED]
hdac0:  nid 28 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0 [DISABLED]
hdac0:  nid 30 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0 [DISABLED]
hdac0:  nid 31 0x00000000 as  0 seq  0      Line-out  Jack jack  0 loc  0 color Unknown misc 0 [DISABLED]
hdac0: Tracing input monitor
hdac0: Tracing beeper
hdac0: GPIO init: data=0x00000000 mask=0x00000000 dir=0x00000000
hdac0: GPIO commit: data=0x00000001 mask=0x00000001 dir=0x00000001
hdac0: FG config/quirks: gpio0 forcestereo ivref50 ivref80 ivref100 ivref
hdac0: 
hdac0: +-------------------+
hdac0: | DUMPING HDA NODES |
hdac0: +-------------------+
hdac0: 
hdac0: Default Parameter
hdac0: -----------------
hdac0:      Stream cap: 0x00000001
hdac0:                  PCM
hdac0:         PCM cap: 0x000e0560
hdac0:                  16 20 24 bits, 44 48 96 192 KHz
hdac0:          IN amp: 0x00000000
hdac0:         OUT amp: 0x00000000
hdac0: 
hdac0:             nid: 2 [DISABLED]
hdac0:            Name: audio output
hdac0:      Widget cap: 0x00000411
hdac0:                  PWR STEREO
hdac0:      Stream cap: 0x00000001
hdac0:                  PCM
hdac0:         PCM cap: 0x000e0560
hdac0:                  16 20 24 bits, 44 48 96 192 KHz
hdac0: 
hdac0:             nid: 3 [DISABLED]
hdac0:            Name: audio output
hdac0:      Widget cap: 0x00000411
hdac0:                  PWR STEREO
hdac0:      Stream cap: 0x00000001
hdac0:                  PCM
hdac0:         PCM cap: 0x000e0560
hdac0:                  16 20 24 bits, 44 48 96 192 KHz
hdac0: 
hdac0:             nid: 4 [DISABLED]
hdac0:            Name: audio output
hdac0:      Widget cap: 0x00000411
hdac0:                  PWR STEREO
hdac0:      Stream cap: 0x00000001
hdac0:                  PCM
hdac0:         PCM cap: 0x000e0160
hdac0:                  16 20 24 bits, 44 48 96 KHz
hdac0: 
hdac0:             nid: 5 [DISABLED]
hdac0:            Name: audio output
hdac0:      Widget cap: 0x00000411
hdac0:                  PWR STEREO
hdac0:      Stream cap: 0x00000001
hdac0:                  PCM
hdac0:         PCM cap: 0x000e0160
hdac0:                  16 20 24 bits, 44 48 96 KHz
hdac0: 
hdac0:             nid: 6 [DISABLED]
hdac0:            Name: audio output
hdac0:      Widget cap: 0x00000211
hdac0:                  DIGITAL STEREO
hdac0:      Stream cap: 0x00000001
hdac0:                  PCM
hdac0:         PCM cap: 0x001e0160
hdac0:                  16 20 24 32 bits, 44 48 96 KHz
hdac0: 
hdac0:             nid: 7 [DISABLED]
hdac0:            Name: audio input
hdac0:      Widget cap: 0x0010051b
hdac0:                  PWR STEREO
hdac0:      Stream cap: 0x00000001
hdac0:                  PCM
hdac0:         PCM cap: 0x00060160
hdac0:                  16 20 bits, 44 48 96 KHz
hdac0:       Input amp: 0x80032300
hdac0:                  mute=1 step=35 size=3 offset=0
hdac0:     connections: 7
hdac0:           |
hdac0:           + [DISABLED] <- nid=24 [pin: Line-out (Jack)] [DISABLED] (selected)
hdac0:           + [DISABLED] <- nid=25 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=26 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=27 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=28 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=20 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=21 [pin: Line-out (Jack)] [DISABLED]
hdac0: 
hdac0:             nid: 8 [DISABLED]
hdac0:            Name: audio input
hdac0:      Widget cap: 0x0010051b
hdac0:                  PWR STEREO
hdac0:      Stream cap: 0x00000001
hdac0:                  PCM
hdac0:         PCM cap: 0x00060160
hdac0:                  16 20 bits, 44 48 96 KHz
hdac0:       Input amp: 0x80032300
hdac0:                  mute=1 step=35 size=3 offset=0
hdac0:     connections: 7
hdac0:           |
hdac0:           + [DISABLED] <- nid=24 [pin: Line-out (Jack)] [DISABLED] (selected)
hdac0:           + [DISABLED] <- nid=25 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=26 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=27 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=28 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=20 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=21 [pin: Line-out (Jack)] [DISABLED]
hdac0: 
hdac0:             nid: 9 [DISABLED]
hdac0:            Name: audio input
hdac0:      Widget cap: 0x0010051b
hdac0:                  PWR STEREO
hdac0:      Stream cap: 0x00000001
hdac0:                  PCM
hdac0:         PCM cap: 0x00060160
hdac0:                  16 20 bits, 44 48 96 KHz
hdac0:       Input amp: 0x80032300
hdac0:                  mute=1 step=35 size=3 offset=0
hdac0:     connections: 10
hdac0:           |
hdac0:           + [DISABLED] <- nid=24 [pin: Line-out (Jack)] [DISABLED] (selected)
hdac0:           + [DISABLED] <- nid=25 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=26 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=27 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=28 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + <- nid=11 [audio mixer] [DISABLED]
hdac0:           + [DISABLED] <- nid=20 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=21 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=22 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=23 [pin: Line-out (Jack)] [DISABLED]
hdac0: 
hdac0:             nid: 10 [DISABLED]
hdac0:            Name: audio input
hdac0:      Widget cap: 0x00100391
hdac0:                  DIGITAL UNSOL STEREO
hdac0:      Stream cap: 0x00000001
hdac0:                  PCM
hdac0:         PCM cap: 0x001e0160
hdac0:                  16 20 24 32 bits, 44 48 96 KHz
hdac0:     connections: 1
hdac0:           |
hdac0:           + [DISABLED] <- nid=31 [pin: Line-out (Jack)] [DISABLED]
hdac0: 
hdac0:             nid: 11 [DISABLED]
hdac0:            Name: audio mixer
hdac0:      Widget cap: 0x0020010b
hdac0:                  STEREO
hdac0:       Input amp: 0x80034123
hdac0:                  mute=1 step=65 size=3 offset=35
hdac0:     connections: 8
hdac0:           |
hdac0:           + [DISABLED] <- nid=24 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=25 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=26 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=27 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=28 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=29 [beep widget]
hdac0:           + [DISABLED] <- nid=20 [pin: Line-out (Jack)] [DISABLED]
hdac0:           + [DISABLED] <- nid=21 [pin: Line-out (Jack)] [DISABLED]
hdac0: 
hdac0:             nid: 12 [DISABLED]
hdac0:            Name: audio mixer
hdac0:      Widget cap: 0x0020010f
hdac0:                  STEREO
hdac0:      Output amp: 0x00034040
hdac0:                  mute=0 step=64 size=3 offset=64
hdac0:       Input amp: 0x80000000
hdac0:                  mute=1 step=0 size=0 offset=0
hdac0:     connections: 2
hdac0:           |
hdac0:           + [DISABLED] <- nid=2 [audio output] [DISABLED]
hdac0:           + [DISABLED] <- nid=11 [audio mixer] [DISABLED]
hdac0: 
hdac0:             nid: 13 [DISABLED]
hdac0:            Name: audio mixer
hdac0:      Widget cap: 0x0020010f
hdac0:                  STEREO
hdac0:      Output amp: 0x00034040
hdac0:                  mute=0 step=64 size=3 offset=64
hdac0:       Input amp: 0x80000000
hdac0:                  mute=1 step=0 size=0 offset=0
hdac0:     connections: 2
hdac0:           |
hdac0:           + [DISABLED] <- nid=3 [audio output] [DISABLED]
hdac0:           + [DISABLED] <- nid=11 [audio mixer] [DISABLED]
hdac0: 
hdac0:             nid: 14 [DISABLED]
hdac0:            Name: audio mixer
hdac0:      Widget cap: 0x0020010f
hdac0:                  STEREO
hdac0:      Output amp: 0x00034040
hdac0:                  mute=0 step=64 size=3 offset=64
hdac0:       Input amp: 0x80000000
hdac0:                  mute=1 step=0 size=0 offset=0
hdac0:     connections: 2
hdac0:           |
hdac0:           + [DISABLED] <- nid=4 [audio output] [DISABLED]
hdac0:           + [DISABLED] <- nid=11 [audio mixer] [DISABLED]
hdac0: 
hdac0:             nid: 15 [DISABLED]
hdac0:            Name: audio mixer
hdac0:      Widget cap: 0x0020010f
hdac0:                  STEREO
hdac0:      Output amp: 0x00034040
hdac0:                  mute=0 step=64 size=3 offset=64
hdac0:       Input amp: 0x80000000
hdac0:                  mute=1 step=0 size=0 offset=0
hdac0:     connections: 2
hdac0:           |
hdac0:           + [DISABLED] <- nid=5 [audio output] [DISABLED]
hdac0:           + [DISABLED] <- nid=11 [audio mixer] [DISABLED]
hdac0: 
hdac0:             nid: 16 [DISABLED]
hdac0:            Name: audio selector
hdac0:      Widget cap: 0x00300101
hdac0:                  STEREO
hdac0:     connections: 4
hdac0:           |
hdac0:           + <- nid=12 [audio mixer] [DISABLED] (selected)
hdac0:           + <- nid=13 [audio mixer] [DISABLED]
hdac0:           + <- nid=14 [audio mixer] [DISABLED]
hdac0:           + <- nid=15 [audio mixer] [DISABLED]
hdac0: 
hdac0:             nid: 17 [DISABLED]
hdac0:            Name: audio selector
hdac0:      Widget cap: 0x00300101
hdac0:                  STEREO
hdac0:     connections: 4
hdac0:           |
hdac0:           + <- nid=12 [audio mixer] [DISABLED] (selected)
hdac0:           + <- nid=13 [audio mixer] [DISABLED]
hdac0:           + <- nid=14 [audio mixer] [DISABLED]
hdac0:           + <- nid=15 [audio mixer] [DISABLED]
hdac0: 
hdac0:             nid: 18 [DISABLED]
hdac0:            Name: audio selector
hdac0:      Widget cap: 0x00300101
hdac0:                  STEREO
hdac0:     connections: 4
hdac0:           |
hdac0:           + <- nid=12 [audio mixer] [DISABLED] (selected)
hdac0:           + <- nid=13 [audio mixer] [DISABLED]
hdac0:           + <- nid=14 [audio mixer] [DISABLED]
hdac0:           + <- nid=15 [audio mixer] [DISABLED]
hdac0: 
hdac0:             nid: 19 [DISABLED]
hdac0:            Name: audio selector
hdac0:      Widget cap: 0x00300101
hdac0:                  STEREO
hdac0:     connections: 4
hdac0:           |
hdac0:           + <- nid=12 [audio mixer] [DISABLED] (selected)
hdac0:           + <- nid=13 [audio mixer] [DISABLED]
hdac0:           + <- nid=14 [audio mixer] [DISABLED]
hdac0:           + <- nid=15 [audio mixer] [DISABLED]
hdac0: 
hdac0:             nid: 20 [DISABLED]
hdac0:            Name: pin: Line-out (Jack)
hdac0:      Widget cap: 0x0040018d
hdac0:                  UNSOL STEREO
hdac0:         Pin cap: 0x0000003f
hdac0:                  ISC TRQD PDC HP OUT IN
hdac0:      Pin config: 0x00000000
hdac0:     Pin control: 0x00000000
hdac0:      Output amp: 0x80000000
hdac0:                  mute=1 step=0 size=0 offset=0
hdac0:     connections: 1
hdac0:           |
hdac0:           + [DISABLED] <- nid=12 [audio mixer] [DISABLED]
hdac0: 
hdac0:             nid: 21 [DISABLED]
hdac0:            Name: pin: Line-out (Jack)
hdac0:      Widget cap: 0x0040018d
hdac0:                  UNSOL STEREO
hdac0:         Pin cap: 0x0000003f
hdac0:                  ISC TRQD PDC HP OUT IN
hdac0:      Pin config: 0x00000000
hdac0:     Pin control: 0x00000000
hdac0:      Output amp: 0x80000000
hdac0:                  mute=1 step=0 size=0 offset=0
hdac0:     connections: 1
hdac0:           |
hdac0:           + [DISABLED] <- nid=13 [audio mixer] [DISABLED]
hdac0: 
hdac0:             nid: 22 [DISABLED]
hdac0:            Name: pin: Line-out (Jack)
hdac0:      Widget cap: 0x0040018d
hdac0:                  UNSOL STEREO
hdac0:         Pin cap: 0x0000003f
hdac0:                  ISC TRQD PDC HP OUT IN
hdac0:      Pin config: 0x00000000
hdac0:     Pin control: 0x00000000
hdac0:      Output amp: 0x80000000
hdac0:                  mute=1 step=0 size=0 offset=0
hdac0:     connections: 1
hdac0:           |
hdac0:           + [DISABLED] <- nid=14 [audio mixer] [DISABLED]
hdac0: 
hdac0:             nid: 23 [DISABLED]
hdac0:            Name: pin: Line-out (Jack)
hdac0:      Widget cap: 0x0040018d
hdac0:                  UNSOL STEREO
hdac0:         Pin cap: 0x0000003f
hdac0:                  ISC TRQD PDC HP OUT IN
hdac0:      Pin config: 0x00000000
hdac0:     Pin control: 0x00000000
hdac0:      Output amp: 0x80000000
hdac0:                  mute=1 step=0 size=0 offset=0
hdac0:     connections: 1
hdac0:           |
hdac0:           + [DISABLED] <- nid=15 [audio mixer] [DISABLED]
hdac0: 
hdac0:             nid: 24 [DISABLED]
hdac0:            Name: pin: Line-out (Jack)
hdac0:      Widget cap: 0x0040018d
hdac0:                  UNSOL STEREO
hdac0:         Pin cap: 0x0000133f
hdac0:                  ISC TRQD PDC HP OUT IN VREF[ 50 80 HIZ ]
hdac0:      Pin config: 0x00000000
hdac0:     Pin control: 0x00000000
hdac0:      Output amp: 0x80000000
hdac0:                  mute=1 step=0 size=0 offset=0
hdac0:     connections: 1
hdac0:           |
hdac0:           + [DISABLED] <- nid=16 [audio selector] [DISABLED]
hdac0: 
hdac0:             nid: 25 [DISABLED]
hdac0:            Name: pin: Line-out (Jack)
hdac0:      Widget cap: 0x0040018d
hdac0:                  UNSOL STEREO
hdac0:         Pin cap: 0x0000133f
hdac0:                  ISC TRQD PDC HP OUT IN VREF[ 50 80 HIZ ]
hdac0:      Pin config: 0x00000000
hdac0:     Pin control: 0x00000000
hdac0:      Output amp: 0x80000000
hdac0:                  mute=1 step=0 size=0 offset=0
hdac0:     connections: 1
hdac0:           |
hdac0:           + [DISABLED] <- nid=17 [audio selector] [DISABLED]
hdac0: 
hdac0:             nid: 26 [DISABLED]
hdac0:            Name: pin: Line-out (Jack)
hdac0:      Widget cap: 0x0040018d
hdac0:                  UNSOL STEREO
hdac0:         Pin cap: 0x0000133f
hdac0:                  ISC TRQD PDC HP OUT IN VREF[ 50 80 HIZ ]
hdac0:      Pin config: 0x00000000
hdac0:     Pin control: 0x00000000
hdac0:      Output amp: 0x80000000
hdac0:                  mute=1 step=0 size=0 offset=0
hdac0:     connections: 1
hdac0:           |
hdac0:           + [DISABLED] <- nid=18 [audio selector] [DISABLED]
hdac0: 
hdac0:             nid: 27 [DISABLED]
hdac0:            Name: pin: Line-out (Jack)
hdac0:      Widget cap: 0x0040018d
hdac0:                  UNSOL STEREO
hdac0:         Pin cap: 0x0000133f
hdac0:                  ISC TRQD PDC HP OUT IN VREF[ 50 80 HIZ ]
hdac0:      Pin config: 0x00000000
hdac0:     Pin control: 0x00000000
hdac0:      Output amp: 0x80000000
hdac0:                  mute=1 step=0 size=0 offset=0
hdac0:     connections: 1
hdac0:           |
hdac0:           + [DISABLED] <- nid=19 [audio selector] [DISABLED]
hdac0: 
hdac0:             nid: 28 [DISABLED]
hdac0:            Name: pin: Line-out (Jack)
hdac0:      Widget cap: 0x00400001
hdac0:                  STEREO
hdac0:         Pin cap: 0x00000020
hdac0:                  IN
hdac0:      Pin config: 0x00000000
hdac0:     Pin control: 0x00000000
hdac0: 
hdac0:             nid: 29
hdac0:            Name: beep widget
hdac0:      Widget cap: 0x00700000
hdac0:     Association: -2 (0x00000000)
hdac0:             OSS: speaker (speaker)
hdac0: 
hdac0:             nid: 30 [DISABLED]
hdac0:            Name: pin: Line-out (Jack)
hdac0:      Widget cap: 0x00400300
hdac0:                  DIGITAL
hdac0:         Pin cap: 0x00000010
hdac0:                  OUT
hdac0:      Pin config: 0x00000000
hdac0:     Pin control: 0x00000000
hdac0:     connections: 1
hdac0:           |
hdac0:           + <- nid=6 [audio output] [DISABLED]
hdac0: 
hdac0:             nid: 31 [DISABLED]
hdac0:            Name: pin: Line-out (Jack)
hdac0:      Widget cap: 0x00400200
hdac0:                  DIGITAL
hdac0:         Pin cap: 0x00000020
hdac0:                  IN
hdac0:      Pin config: 0x00000000
hdac0:     Pin control: 0x00000000
hdac0: 
hdac0:             nid: 32 [DISABLED]
hdac0:            Name: vendor widget
hdac0:      Widget cap: 0x00f00040
hdac0:                  PROC
hdac0: 
hdac0:             nid: 33 [DISABLED]
hdac0:            Name: volume widget
hdac0:      Widget cap: 0x00600080
hdac0:                  UNSOL
hdac0: 
hdac0: Processing modem FG cad=1 nid=1...
hdac0: 
found->	vendor=0x8086, dev=0x266a, revid=0x04
	domain=0, bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=19
pci0:0:31:3: reprobing on driver added
pci1: driver added
pci2: driver added
pci6: driver added
found->	vendor=0x8086, dev=0x4223, revid=0x05
	domain=0, bus=6, slot=3, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0012, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D3  current D0
pci0:6:3:0: reprobing on driver added
found->	vendor=0x1217, dev=0x7110, revid=0x00
	domain=0, bus=6, slot=9, func=2
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0003, statreg=0x0410, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0:6:9:2: reprobing on driver added
pci9: driver added
pci10: driver added
pci0: driver added
found->	vendor=0x8086, dev=0x266a, revid=0x04
	domain=0, bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=19
pci0:0:31:3: reprobing on driver added
pci1: driver added
pci2: driver added
pci6: driver added
found->	vendor=0x8086, dev=0x4223, revid=0x05
	domain=0, bus=6, slot=3, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0012, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D3  current D0
pci0:6:3:0: reprobing on driver added
found->	vendor=0x1217, dev=0x7110, revid=0x00
	domain=0, bus=6, slot=9, func=2
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0003, statreg=0x0410, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0:6:9:2: reprobing on driver added
pci9: driver added
pci10: driver added
acpi_hpet0: <High Precision Event Timer> iomem 0-0x3ff on acpi0
device_attach: acpi_hpet0 attach returned 12
sio4: irq maps: 0xc01 0xc01 0xc01 0xc01
sio4: probe failed test(s): 1 4 6 9
ppc0: using extended I/O port range
pci0: driver added
found->	vendor=0x8086, dev=0x266a, revid=0x04
	domain=0, bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=19
pci0:0:31:3: reprobing on driver added
pci1: driver added
pci2: driver added
pci6: driver added
found->	vendor=0x8086, dev=0x4223, revid=0x05
	domain=0, bus=6, slot=3, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0012, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D3  current D0
pci0:6:3:0: reprobing on driver added
found->	vendor=0x1217, dev=0x7110, revid=0x00
	domain=0, bus=6, slot=9, func=2
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0003, statreg=0x0410, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0:6:9:2: reprobing on driver added
pci9: driver added
pci10: driver added
pci0: driver added
found->	vendor=0x8086, dev=0x266a, revid=0x04
	domain=0, bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=19
pci0:0:31:3: reprobing on driver added
pci1: driver added
pci2: driver added
pci6: driver added
found->	vendor=0x8086, dev=0x4223, revid=0x05
	domain=0, bus=6, slot=3, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0012, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D3  current D0
pci0:6:3:0: reprobing on driver added
found->	vendor=0x1217, dev=0x7110, revid=0x00
	domain=0, bus=6, slot=9, func=2
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0003, statreg=0x0410, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0:6:9:2: reprobing on driver added
pci9: driver added
pci10: driver added
pci0: driver added
found->	vendor=0x8086, dev=0x266a, revid=0x04
	domain=0, bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=19
pci0:0:31:3: reprobing on driver added
pci1: driver added
pci2: driver added
pci6: driver added
found->	vendor=0x8086, dev=0x4223, revid=0x05
	domain=0, bus=6, slot=3, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0012, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D3  current D0
pci0:6:3:0: reprobing on driver added
found->	vendor=0x1217, dev=0x7110, revid=0x00
	domain=0, bus=6, slot=9, func=2
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0003, statreg=0x0410, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0:6:9:2: reprobing on driver added
pci9: driver added
pci10: driver added
pci0: driver added
found->	vendor=0x8086, dev=0x266a, revid=0x04
	domain=0, bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=19
pci0:0:31:3: reprobing on driver added
pci1: driver added
pci2: driver added
pci6: driver added
found->	vendor=0x8086, dev=0x4223, revid=0x05
	domain=0, bus=6, slot=3, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0012, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D3  current D0
pci0:6:3:0: reprobing on driver added
found->	vendor=0x1217, dev=0x7110, revid=0x00
	domain=0, bus=6, slot=9, func=2
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0003, statreg=0x0410, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0:6:9:2: reprobing on driver added
pci9: driver added
pci10: driver added
pci0: driver added
found->	vendor=0x8086, dev=0x266a, revid=0x04
	domain=0, bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=19
pci0:0:31:3: reprobing on driver added
pci1: driver added
pci2: driver added
pci6: driver added
found->	vendor=0x8086, dev=0x4223, revid=0x05
	domain=0, bus=6, slot=3, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0012, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D3  current D0
pci0:6:3:0: reprobing on driver added
found->	vendor=0x1217, dev=0x7110, revid=0x00
	domain=0, bus=6, slot=9, func=2
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0003, statreg=0x0410, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0:6:9:2: reprobing on driver added
pci9: driver added
pci10: driver added
pci0: driver added
found->	vendor=0x8086, dev=0x266a, revid=0x04
	domain=0, bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=19
pci0:0:31:3: reprobing on driver added
pci1: driver added
pci2: driver added
pci6: driver added
found->	vendor=0x8086, dev=0x4223, revid=0x05
	domain=0, bus=6, slot=3, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0012, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D3  current D0
pci0:6:3:0: reprobing on driver added
found->	vendor=0x1217, dev=0x7110, revid=0x00
	domain=0, bus=6, slot=9, func=2
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0003, statreg=0x0410, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0:6:9:2: reprobing on driver added
pci9: driver added
pci10: driver added
pci0: driver added
found->	vendor=0x8086, dev=0x266a, revid=0x04
	domain=0, bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=19
pci0:0:31:3: reprobing on driver added
pci1: driver added
pci2: driver added
pci6: driver added
found->	vendor=0x8086, dev=0x4223, revid=0x05
	domain=0, bus=6, slot=3, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0012, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D3  current D0
pci0:6:3:0: reprobing on driver added
found->	vendor=0x1217, dev=0x7110, revid=0x00
	domain=0, bus=6, slot=9, func=2
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0003, statreg=0x0410, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0:6:9:2: reprobing on driver added
pci9: driver added
pci10: driver added
pci0: driver added
found->	vendor=0x8086, dev=0x266a, revid=0x04
	domain=0, bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=19
pci0:0:31:3: reprobing on driver added
pci1: driver added
pci2: driver added
pci6: driver added
found->	vendor=0x8086, dev=0x4223, revid=0x05
	domain=0, bus=6, slot=3, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0012, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D3  current D0
pci0:6:3:0: reprobing on driver added
found->	vendor=0x1217, dev=0x7110, revid=0x00
	domain=0, bus=6, slot=9, func=2
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0003, statreg=0x0410, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0:6:9:2: reprobing on driver added
pci9: driver added
pci10: driver added
pci0: driver added
found->	vendor=0x8086, dev=0x266a, revid=0x04
	domain=0, bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=19
pci0:0:31:3: reprobing on driver added
pci1: driver added
pci2: driver added
pci6: driver added
found->	vendor=0x8086, dev=0x4223, revid=0x05
	domain=0, bus=6, slot=3, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0012, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D3  current D0
pci0:6:3:0: reprobing on driver added
found->	vendor=0x1217, dev=0x7110, revid=0x00
	domain=0, bus=6, slot=9, func=2
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0003, statreg=0x0410, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0:6:9:2: reprobing on driver added
pci9: driver added
pci10: driver added
pci0: driver added
found->	vendor=0x8086, dev=0x266a, revid=0x04
	domain=0, bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=19
pci0:0:31:3: reprobing on driver added
pci1: driver added
pci2: driver added
pci6: driver added
found->	vendor=0x8086, dev=0x4223, revid=0x05
	domain=0, bus=6, slot=3, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0012, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=17
	powerspec 2  supports D0 D3  current D0
pci0:6:3:0: reprobing on driver added
found->	vendor=0x1217, dev=0x7110, revid=0x00
	domain=0, bus=6, slot=9, func=2
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0003, statreg=0x0410, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0:6:9:2: reprobing on driver added
pci9: driver added
pci10: driver added
acpi_hpet0: <High Precision Event Timer> iomem 0-0x3ff on acpi0
device_attach: acpi_hpet0 attach returned 12
sio4: irq maps: 0xc01 0xc01 0xc01 0xc01
sio4: probe failed test(s): 1 4 6 9
ppc0: using extended I/O port range
 
Aber nach einem "kldunload snd_driver.ko" und einem "soundon" von oss war auf einmal das hier möglich:

$ ls /dev/dsp*
/dev/dsp /dev/dsp14 /dev/dsp8
/dev/dsp0 /dev/dsp2 /dev/dsp9
/dev/dsp1 /dev/dsp3 /dev/dsp_ac3
/dev/dsp10 /dev/dsp4 /dev/dsp_in
/dev/dsp11 /dev/dsp5 /dev/dsp_mmap
/dev/dsp12 /dev/dsp6 /dev/dsp_multich
/dev/dsp13 /dev/dsp7 /dev/dsp_out


Man bekommt zwar sound, osstest funktioniert, aber kmixer kann wohl den oss nicht steuern.
Und möglicherweise stimmt tatsächlich etwas nicht mit dem snd_hda.ko, wegen der Ausgabe =-1, wie hier vermutet wurde.

BTW: Die Erstellung meines letzten Beitrags schien anfangs nicht zu klappen, so daß ich den mehrmals erstellt habe. Wie kann ich diese löschen? Wenn ich mit der Maus auf den Button "EDIT" gehe, heißt es zwar "Beitrag bearbeiten/löschen", aber ich kann nur editieren und muß mindestens ein Zeichen eingeben?
 
Last edited:
aber kmixer kann wohl den oss nicht steuern.

zumindest bei den KDE vor 4er Versionen konnte OSS benutzt werden und kmix entsprechend auch darauf zugreifen. OSS war das erste Soundsystem, das ich mit KDE wirklich zufriedenstellend nutzte.
Im Kontrollzentrum (ALT+F2 kcontrol) unter "Sound und Multimedia" - "Sound System" - "Hardware" kann Hardware ausgewählt werden und ist dann von KDE nutzbar. Dort gibt es eben auch OSS, wenn es installiert ist.

Vielleicht hilft das ein wenig.
 
Back
Top