Intel Graphics Media Accelerator 900

H

Hanno_Becker

Member
Hallo.

Ich benutze FreeBSD 6.0 Release auf einem Dell Inspiron 630m. Dieser ist mit einer Intel Graphics Media Accelerator 900 Grafikkarte ausgestattet, für die ich Treiber für FreeBSD suche. Bisher laufe ich X mit dem VESA-Treiber; dies hat zur Folge, dass die maximale Auflösung, die ich erhalte, nur 1024x768 ist. Ferner hat das Bild eine schlechte "Qualität".
Ich versuchte

Code: 
Section "Device"
        Identifier  "Card0"
        Driver      "i810"
        ChipSet     "915G"
        Card        "i810 915G"
EndSection
,

erhalte dann jedoch beim Versuch, X zu starten, die Meldung

(EE): i810(0): No valid FB Address in config space.

Kann mir jemand beim Einrichten/der Installation des korrekten Treibers helfen?


Liebe Grüße,
Hanno
 
Wenn ich mich recht erinnere, wird diese GPU erst ab X11R6.9 bzw. X11R7 unterstützt. Guck mal in die Manpage, ob dein Chip dort schon aufgeführt wird, ansonsten mußt du dir das neueste X.org installieren.
 
Hallo.

Danke für deine Antwort. Meine X-Version ist 6.8.2. Ich werde gleich ein Update durchführen und mich dann melden, falls es immernoch nicht funktionieren sollte.

Vielen Dank.


Liebe Grüße,
Hanno
 
Hallo.

Danke walt. Das werde ich auch versuchen. Die Kompilation von Xorg 6.9 schlägt leider fehl. Ich erhalte:

/usr/bin/ld: cannot find -resolv


Liebe Grüße,
Hanno
 
Hallo walt.

Ich benutze noch weiterhin XOrg 6.82, das Hinzufügen des von dir genannten Paketes hat jedoch keine Veränderung gebracht. Es tritt nachwievor der gleiche Fehler auf.


Viele Grüße,
Hanno
 
Enthalten ist ein kleines Tool, das das ins RAM kopierte Video-BIOS patcht.
Das Tool "915resolution" aendert die Aufloesung.
Nach jedem reboot ist die Wirkung des Patch dahin.
Ein Eintrag in /etc/rc.local waere also ganz nuetzlich.
In der +DESC ist ein Link auf die Seite mit dem Quelltext; den zu besorgen
und sich damit zu beschaeftigen waere nicht verkehrt.

Nebenbei: X11R7.0 ist ebenfalls released.
Gleicher Stand wie X11R6.9 nur modularisiert und autotooled.
Bei Interesse daran ist vermutlich ebenfalls eine Auseinandersetzung mit
dem Quelltext notwendig, da ich nicht galube, dass es bereits einen Port gibt.

Hanno_Becker schrieb:
/usr/bin/ld: cannot find -resolv
Zum Vergrößern anklicken....

Es heisst nicht -resolv sondern -lresolv
locate libresolv
 
Zuletzt bearbeitet:
Hallo walt.

Das "-resolv" anstat "-lresolv" war ein Tipfehler meinerseits. Im Fehler heißt es "-lresolv". Ein locate "libresolv" liefert
/usr/compat/linux/lib/libresolv-2.3.2.so
/usr/compat/linux/lib/libresolv.so.2.

Wo kann ich mir XOrg 7 herunterladen? Ich habe auf der Website X.org nur viele kleinere Einzeldateien gefunden, nicht aber ein "Paket", in dem alles enthalten ist.

915resolution bewirkt bisher nichts; aber solange der i810 Treiber nicht angenommen wird, ist das wohl kein Wunder.

Liebe Grüße,
Hanno
 
Hallo walt.

Danke für den Link.

Inzwischen habe ich eine Auflösung von 1280 x 800 mit Hilfe von 915 resolution hinbekommen. Es sieht schon besser aus als vorher, aber etwas "merkwürdig" - vielleicht aber auch nur, weil es für mich ungewohnt ist. Andererseits: ist es notwendig, in der xorg.conf bei widescreen Bildschirmen besondere Optionen zu setzen?
Der i810 Treiber funktioniert nachwievor nicht.

Liebe Grüße,
Hanno
 
die sache mit dem i810 treiber wird was größers, und unter 6.0 warscheinlich nicht zu machen sein.

hatte das gleich problem auf einem ibm r52 mir dem 915gm chipsatz. ewiges rumprobieren hat mich auch nicht weiter gebracht, bis ich auf diesen link gestossen bin :
http://lists.freebsd.org/pipermail/freebsd-current/2005-December/058660.html

danach war die sache klar : update auf current und xorg-server-6.8.99.903 und jetzt tut die sache.

dmesg zu dem thema:
Code: 
....
vgapci0: <VGA-compatible display> port 0x1800-0x1807 mem 0x90080000-0x900fffff,0xb0000000-0xbfffffff,0x90000000-0x9003ffff irq 11 at device 2.0 on pci0
agp0: <Intel 82915GM (915GM GMCH) SVGA controller> on vgapci0
agp0: detected 7932k stolen memory
agp0: aperture size is 256M
drm0: <Intel i915GM> on vgapci0
info: [drm] AGP at 0x90080000 0MB
info: [drm] Initialized i915 1.2.0 20041217
vgapci1: <VGA-compatible display> at device 2.1 on pci0
...

und die xorg.conf :
Code: 
...
Section "Device"
        Option     "DRI"                         
        Option     "NoDDC"                      
        Option     "PageFlip"                  
        Identifier  "Card0"
        Driver      "i810"
        VendorName  "Intel Corporation"
        BoardName   "Mobile 915GM/GMS/910GML Express Graphics Controller"
        BusID       "PCI:0:2:0"
EndSection
...


viele grüße

sg
 
Hanno_Becker schrieb:
Hallo walt.
915resolution bewirkt bisher nichts; aber solange der i810 Treiber nicht angenommen wird, ist das wohl kein Wunder.
Zum Vergrößern anklicken....
Der i810 ist doch der alte Intel Extreme Graphics, bin sicher das der i915 einen ganz anderen Treiber braucht, weil der mehr 3d Functionen hat und ganz anders aufgebaut ist
 
@ anja: falsch, steht in der manpage zum treiber (bsd 6.0)

@ rest: hab den 915g hier am laufen, mit bsd 6.0 und ner aufloesung von 1280x1024.

haut gut hin


greetz
 
Zuletzt bearbeitet:
k

hier alles in einem file, alles sehr standard...






Code: 
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 6.0-RELEASE #0: Thu Nov  3 09:36:13 UTC 2005
    root@x64.samsco.home:/usr/obj/usr/src/sys/GENERIC
ACPI APIC Table: <INTEL  D915GMH >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (3000.00-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf43  Stepping = 3
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x649d<SSE3,RSVD2,MON,DS_CPL,EST,CNTX-ID,CX16,<b14>>
  AMD Features=0x20100000<NX,LM>
  Hyperthreading: 2 logical CPUs
real memory  = 1064497152 (1015 MB)
avail memory = 1028587520 (980 MB)
ioapic0 <Version 2.0> irqs 0-23 on motherboard
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <INTEL D915GMH> on motherboard
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi0: Power Button (fixed)
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
pci_link0: <ACPI PCI Link LNKA> irq 11 on acpi0
pci_link1: <ACPI PCI Link LNKB> irq 0 on acpi0
pci_link2: <ACPI PCI Link LNKC> irq 5 on acpi0
pci_link3: <ACPI PCI Link LNKD> irq 10 on acpi0
pci_link4: <ACPI PCI Link LNKE> irq 0 on acpi0
pci_link5: <ACPI PCI Link LNKF> irq 3 on acpi0
pci_link6: <ACPI PCI Link LNKG> irq 9 on acpi0
pci_link7: <ACPI PCI Link LNKH> irq 9 on acpi0
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci0: <display, VGA> at device 2.0 (no driver attached)
pci0: <multimedia> at device 27.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pci5: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> at device 28.1 on pci0
pci4: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> at device 28.2 on pci0
pci3: <ACPI PCI bus> on pcib4
pcib5: <ACPI PCI-PCI bridge> at device 28.3 on pci0
pci2: <ACPI PCI bus> on pcib5
pci2: <network, ethernet> at device 0.0 (no driver attached)
uhci0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> port 0xc800-0xc81f irq 23 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> port 0xcc00-0xcc1f irq 19 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> port 0xd000-0xd01f irq 18 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> port 0xd400-0xd41f irq 16 at device 29.3 on pci0
uhci3: [GIANT-LOCKED]
usb3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xffa3f800-0xffa3fbff irq 23 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <EHCI (generic) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci6: <ACPI PCI bus> on pcib6
xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0xb800-0xb87f mem 0xff8ffc00-0xff8ffc7f irq 21 at device 0.0 on pci6
miibus0: <MII bus> on xl0
xlphy0: <3Com internal media interface> on miibus0
xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: Ethernet address: 00:10:5a:64:d8:15
pci6: <multimedia, audio> at device 1.0 (no driver attached)
pci6: <input device> at device 1.1 (no driver attached)
fwohci0: <1394 Open Host Controller Interface> mem 0xff8ff000-0xff8ff7ff,0xff8f8000-0xff8fbfff irq 21 at device 1.2 on pci6
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:02:3c:00:91:02:67:5c
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:02:3c:02:67:5c
fwe0: Ethernet address: 02:02:3c:02:67:5c
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH6 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
atapci1: <Intel ICH6 SATA150 controller> port 0xe800-0xe807,0xe400-0xe403,0xe000-0xe007,0xdc00-0xdc03,0xd800-0xd80f mem 0xffa3fc00-0xffa3ffff irq 19 at device 31.2 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
ata4: <ATA channel 2> on atapci1
ata5: <ATA channel 3> on atapci1
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse Explorer, device ID 4
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 3000004680 Hz quality 800
Timecounters tick every 1.000 msec
md0: Preloaded image </boot/mfsroot> 4423680 bytes at 0xc0a3070c
ad0: 78533MB <HDS722580VLAT20 V32OA60A> at ata0-master UDMA100
acd0: DVDR <NEC DVD RW ND-1300A/1.0C> at ata0-slave UDMA33
Trying to mount root from ufs:/dev/md0
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...2 1 0 0 done
All buffers synced.
Uptime: 8m59s
Shutting down ACPI
Rebooting...
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 6.0-RELEASE #0: Thu Nov  3 09:36:13 UTC 2005
    root@x64.samsco.home:/usr/obj/usr/src/sys/GENERIC
ACPI APIC Table: <INTEL  D915GMH >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (3000.00-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf43  Stepping = 3
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x649d<SSE3,RSVD2,MON,DS_CPL,EST,CNTX-ID,CX16,<b14>>
  AMD Features=0x20100000<NX,LM>
  Hyperthreading: 2 logical CPUs
real memory  = 1064497152 (1015 MB)
avail memory = 1032777728 (984 MB)
ioapic0 <Version 2.0> irqs 0-23 on motherboard
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <INTEL D915GMH> on motherboard
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi0: Power Button (fixed)
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
pci_link0: <ACPI PCI Link LNKA> irq 11 on acpi0
pci_link1: <ACPI PCI Link LNKB> irq 0 on acpi0
pci_link2: <ACPI PCI Link LNKC> irq 5 on acpi0
pci_link3: <ACPI PCI Link LNKD> irq 10 on acpi0
pci_link4: <ACPI PCI Link LNKE> irq 0 on acpi0
pci_link5: <ACPI PCI Link LNKF> irq 3 on acpi0
pci_link6: <ACPI PCI Link LNKG> irq 9 on acpi0
pci_link7: <ACPI PCI Link LNKH> irq 9 on acpi0
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci0: <display, VGA> at device 2.0 (no driver attached)
pci0: <multimedia> at device 27.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pci5: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> at device 28.1 on pci0
pci4: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> at device 28.2 on pci0
pci3: <ACPI PCI bus> on pcib4
pcib5: <ACPI PCI-PCI bridge> at device 28.3 on pci0
pci2: <ACPI PCI bus> on pcib5
pci2: <network, ethernet> at device 0.0 (no driver attached)
uhci0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> port 0xc800-0xc81f irq 23 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> port 0xcc00-0xcc1f irq 19 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> port 0xd000-0xd01f irq 18 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> port 0xd400-0xd41f irq 16 at device 29.3 on pci0
uhci3: [GIANT-LOCKED]
usb3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xffa3f800-0xffa3fbff irq 23 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <EHCI (generic) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci6: <ACPI PCI bus> on pcib6
xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0xb800-0xb87f mem 0xff8ffc00-0xff8ffc7f irq 21 at device 0.0 on pci6
miibus0: <MII bus> on xl0
xlphy0: <3Com internal media interface> on miibus0
xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: Ethernet address: 00:10:5a:64:d8:15
pci6: <multimedia, audio> at device 1.0 (no driver attached)
pci6: <input device> at device 1.1 (no driver attached)
fwohci0: <1394 Open Host Controller Interface> mem 0xff8ff000-0xff8ff7ff,0xff8f8000-0xff8fbfff irq 21 at device 1.2 on pci6
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:02:3c:00:91:02:67:5c
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:02:3c:02:67:5c
fwe0: Ethernet address: 02:02:3c:02:67:5c
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH6 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
atapci1: <Intel ICH6 SATA150 controller> port 0xe800-0xe807,0xe400-0xe403,0xe000-0xe007,0xdc00-0xdc03,0xd800-0xd80f mem 0xffa3fc00-0xffa3ffff irq 19 at device 31.2 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
ata4: <ATA channel 2> on atapci1
ata5: <ATA channel 3> on atapci1
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse Explorer, device ID 4
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 3000002100 Hz quality 800
Timecounters tick every 1.000 msec
ad0: 78533MB <HDS722580VLAT20 V32OA60A> at ata0-master UDMA100
acd0: DVDR <NEC DVD RW ND-1300A/1.0C> at ata0-slave UDMA33
Trying to mount root from ufs:/dev/ad0s1a
ums0: Logitech USB-PS/2 Optical Mouse, rev 2.00/11.10, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.

ENDE DMESG


ANFANG xorg.conf



# File generated by xorgconfig.

#
# Copyright 2004 The X.Org Foundation
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
# 
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
# 
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
# The X.Org Foundation BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
# 
# Except as contained in this notice, the name of The X.Org Foundation shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from
# The X.Org Foundation.
#

# **********************************************************************
# Refer to the xorg.conf(5) man page for details about the format of 
# this file.
# **********************************************************************

# **********************************************************************
# Module section -- this  section  is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"

# This loads the DBE extension module.

    Load        "dbe"  	# Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
    SubSection  "extmod"
      Option    "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection

# This loads the font modules
    Load        "type1"
#    Load        "speedo"
    Load        "freetype"
#    Load        "xtt"

# This loads the GLX module
#    Load       "glx"
# This loads the DRI module
#    Load       "dri"

EndSection

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    RgbPath	"/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
# 
# 

    FontPath   "/usr/X11R6/lib/X11/fonts/misc/"
    FontPath   "/usr/X11R6/lib/X11/fonts/TTF/"
#    FontPath   "/usr/X11R6/lib/X11/fonts/Type1/"
#    FontPath   "/usr/X11R6/lib/X11/fonts/CID/"
    FontPath   "/usr/X11R6/lib/X11/fonts/75dpi/"
    FontPath   "/usr/X11R6/lib/X11/fonts/100dpi/"
    FontPath   "/usr/X11R6/lib/X11/fonts/local/"
#    FontPath   "/usr/X11R6/lib/X11/fonts/Speedo/"
#    FontPath   "/usr/X11R6/lib/X11/fonts/TrueType/"
#    FontPath   "/usr/X11R6/lib/X11/fonts/freefont/"

# The module search path.  The default path is shown here.

#    ModulePath "/usr/X11R6/lib/modules"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is 
# received.  This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

#    Option "NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12).  This allows clients to receive these key
# events.

#    Option "DontVTSwitch"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

#    Option "DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences.  This allows clients to receive these key events.

#    Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

#    Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client. 

#    Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings. 

#    Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

#    Option "AllowNonLocalModInDev"

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

    Identifier	"Keyboard1"
    Driver	"kbd"

# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

#    Option     "Protocol"      "Xqueue"

    Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
#    Option	"Xleds"      "1 2 3"

#    Option "LeftAlt"     "Meta"
#    Option "RightAlt"    "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#    Option "XkbModel"    "pc105"
# If you have a US Microsoft Natural keyboard, you can use:
#    Option "XkbModel"    "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#    Option "XkbLayout"   "de"
# or:
#    Option "XkbLayout"   "de"
#    Option "XkbVariant"  "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#    Option "XkbOptions"  "ctrl:swapcaps"

# These are the default XKB settings for Xorg
#    Option "XkbRules"    "xorg"
#    Option "XkbModel"    "pc105"
#    Option "XkbLayout"   "us"
#    Option "XkbVariant"  ""
#    Option "XkbOptions"  ""

#    Option "XkbDisable"

    Option "XkbRules"	"xorg"
    Option "XkbModel"	"pc105"
    Option "XkbLayout"	"us"

EndSection


# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

    Identifier	"Mouse1"
    Driver	"mouse"
    Option "Protocol"    "auto"
    Option "Device"      "/dev/sysmouse"

# Mouse-speed setting for PS/2 mouse.

#    Option "Resolution"	"256"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Option "Protocol"	"Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

#    Option "BaudRate"	"9600"
#    Option "SampleRate"	"150"

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

#    Option "Emulate3Buttons"
#    Option "Emulate3Timeout"    "50"

# ChordMiddle is an option for some 3-button Logitech mice

#    Option "ChordMiddle"

EndSection


# **********************************************************************
# Other input device sections 
# this is optional and is required only if you
# are using extended input devices.  This is for example only.  Refer
# to the xorg.conf man page for a description of the options.
# **********************************************************************
#
# Section "InputDevice" 
#    Identifier  "Mouse2"
#    Driver      "mouse"
#    Option      "Protocol"      "MouseMan"
#    Option      "Device"        "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball"
#    Driver     "magellan"
#    Option     "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball2"
#    Driver     "spaceorb"
#    Option     "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen0"
#    Driver     "microtouch"
#    Option     "Device"        "/dev/ttyS0"
#    Option     "MinX"          "1412"
#    Option     "MaxX"          "15184"
#    Option     "MinY"          "15372"
#    Option     "MaxY"          "1230"
#    Option     "ScreenNumber"  "0"
#    Option     "ReportingMode" "Scaled"
#    Option     "ButtonNumber"  "1"
#    Option     "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen1"
#    Driver     "elo2300"
#    Option     "Device"        "/dev/ttyS0"
#    Option     "MinX"          "231"
#    Option     "MaxX"          "3868"
#    Option     "MinY"          "3858"
#    Option     "MaxY"          "272"
#    Option     "ScreenNumber"  "0"
#    Option     "ReportingMode" "Scaled"
#    Option     "ButtonThreshold"       "17"
#    Option     "ButtonNumber"  "1"
#    Option     "SendCoreEvents"
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "EZ"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    HorizSync   30-130

#    HorizSync	30-64         # multisync
#    HorizSync	31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync	15-25, 30-50  # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    VertRefresh 50-160

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
    Identifier	"Standard VGA"
    VendorName	"Unknown"
    BoardName	"Unknown"

# The chipset line is optional in most cases.  It can be used to override
# the driver's chipset detection, and should not normally be specified.

#    Chipset	"generic"

# The Driver line must be present.  When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module.  Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

    Driver     "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for.  When this line isn't present, a device
# section can only match up with the primary video device.  For PCI
# devices a line like the following could be used.  This line should not
# normally be included unless there is more than one video device
# intalled.

#    BusID      "PCI:0:10:0"

#    VideoRam	256

#    Clocks	25.2 28.3

EndSection

# Device configured by xorgconfig:

Section "Device"
    Identifier  "G"
    Driver      "i810"
    #VideoRam    32768
    # Insert Clocks lines here if appropriate
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
    Identifier  "Screen 1"
    Device      "G"
    Monitor     "EZ"
    DefaultDepth 24

    Subsection "Display"
        Depth       8
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       24
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
    Identifier  "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.  In this example, screen 2 is located to the
# right of screen 1.

    Screen "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"

EndSection

# Section "DRI"
#    Mode 0666
# EndSection


greetz
 
Du musst dich einloggen oder registrieren, um hier zu antworten.
Zurück
Oben