kein sound nach update auf FreeBSD 5.4

A

ACID25

PolytoXikomane
Hallo
ich habe gestern mein system von 5.3 --> 5.4 gebracht. Es hat auch alles funktioniert soweit ;) nur habe ich nun keinen sound mehr :(
unter 5.3 lief alles einwandfrei unter 5.4 leider nicht mehr. Soundchip ist der fm801

dmesg
[ code]
pci0: <serial bus, SMBus> at device 1.1 (no driver attached)
[/code]

cat /dev/sndstat
Code: 
FreeBSD Audio Driver (newpcm)
Installed devices:


in der loder.conf steht
Code: 
cat /boot/loader.conf
autoboot_delay="3"
loader_color="YES"
snd_fm801_load="YES"
linux_load="YES"
nvidia_load="YES"

kldstat
Code: 
kldstat
Id Refs Address    Size     Name
 1   14 0xc0400000 41e834   kernel
 2    6 0xc081f000 1e8ac    linux.ko
 3    1 0xc083e000 5174     snd_fm801.ko
 4    1 0xc0844000 4aea88   nvidia.ko
 5   14 0xc0cf3000 60270    acpi.ko
 6    1 0xc2d12000 9000     vmmon_up.ko
 7    1 0xc2d1b000 2000     vmnet.ko
 8    1 0xc2d48000 2000     rtc.ko
hat sich evtl. zwischen der 5.3 und 5.4 was verändert bei der sound config?

vielen dank fürr eure hilfe
ACID25
 
hi
ups stimmt ist ja gar nicht das sound device :o
kommt davon wenn man alles in hektik macht ;)
Code: 
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.4-STABLE #0: Tue May 10 23:41:10 CEST 2005
    olly@tuxi.tibet.serveftp.net:/usr/obj/usr/src/sys/TUXI050405
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) XP 2600+ (1921.04-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x6a0  Stepping = 0
  Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
  AMD Features=0xc0400000<AMIE,DSP,3DNow!>
real memory  = 1073676288 (1023 MB)
avail memory = 1037209600 (989 MB)
mptable_probe: Unable to map end of MP Config Table
ACPI APIC Table: <Nvidia AWRDACPI>
ioapic0 <Version 1.1> irqs 0-23 on motherboard
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <Nvidia AWRDACPI> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <memory, RAM> at device 0.1 (no driver attached)
pci0: <memory, RAM> at device 0.2 (no driver attached)
pci0: <memory, RAM> at device 0.3 (no driver attached)
pci0: <memory, RAM> at device 0.4 (no driver attached)
pci0: <memory, RAM> at device 0.5 (no driver attached)
isab0: <PCI-ISA bridge> at device 1.0 on pci0
isa0: <ISA bus> on isab0
pci0: <serial bus, SMBus> at device 1.1 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xe0000000-0xe0000fff irq 22 at device 2.0 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xe0003000-0xe0003fff irq 21 at device 2.1 on pci0
usb1: OHCI version 1.0, legacy support
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xe0004000-0xe00040ff irq 20 at device 2.2 on pci0
usb2: EHCI version 1.0
usb2: companion controllers, 4 ports each: usb0 usb1
usb2: <EHCI (generic) USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 6 ports with 6 removable, self powered
pcib1: <ACPI PCI-PCI bridge> at device 8.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <multimedia, audio> at device 7.0 (no driver attached)
pci1: <input device> at device 7.1 (no driver attached)
xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0xd800-0xd87f mem 0xdf801000-0xdf80107f irq 17 at device 9.0 on pci1
miibus0: <MII bus> on xl0
xlphy0: <3Com internal media interface> on miibus0
xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: Ethernet address: 00:01:02:f5:04:d9
twe0: <3ware Storage Controller. Driver version 1.50.01.002> port 0xdc00-0xdc0f mem 0xdf000000-0xdf7fffff irq 16 at device 10.0 on pci1
twe0: 2 ports, Firmware FE7X 1.05.00.056, BIOS BE7X 1.08.00.046
atapci0: <nVidia nForce2 UDMA133 controller> port 0xf000-0xf00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 9.0 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
fwohci0: <1394 Open Host Controller Interface> mem 0xe0002000-0xe000203f,0xe0001000-0xe00017ff irq 22 at device 13.0 on pci0
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:e0:18:00:00:3f:81:54
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc1, gen=1, CYCLEMASTER mode
firewire0: 2 nodes, maxhop <= 1, cable IRM = 1 (me)
firewire0: bus manager 1 (me)
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
nvidia0: <GeForce FX 5200> mem 0xd0000000-0xd7ffffff,0xdc000000-0xdcffffff irq 19 at device 0.0 on pci2
fdc0: <floppy drive controller> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <ECP parallel printer port> port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc0
ppbus0: IEEE1284 device found /NIBBLE/ECP
Probing for PnP devices on ppbus0:
ppbus0: <hp deskjet 5550> PRINTER MLC,PCL,PML,DW-PCL,DYN,DESKJET
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model MouseMan+, device ID 0
orm0: <ISA Option ROMs> at iomem 0xd0000-0xd0fff,0xc0000-0xcf7ff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1921035521 Hz quality 800
Timecounters tick every 10.000 msec
ad0: 78533MB <IC35L080AVVA07-0/VA4OA52A> [159560/16/63] at ata0-master UDMA100
ad1: 78533MB <IC35L080AVVA07-0/VA4OA52A> [159560/16/63] at ata0-slave UDMA100
acd0: DVDROM <TOSHIBA DVD-ROM SD-M1502/1012> at ata1-master PIO4
acd1: DVDR <PIONEER DVD-RW DVR-105/1.33> at ata1-slave PIO4
twed0: <Unit 0, RAID0, Normal> on twe0
twed0: 381562MB (781439744 sectors)
firewire0: New S400 device ID:000a270002d8997b
da0 at sbp0 bus 0 target 0 lun 0
da0: <Apple Co iPod 2700> Removable Simplified Direct Access SCSI-0 device
da0: 50.000MB/s transfers
da0: 38147MB (78126048 512 byte sectors: 255H 63S/T 4863C)
cd0 at ata1 bus 0 target 0 lun 0
cd0: <TOSHIBA DVD-ROM SD-M1502 1012> Removable CD-ROM SCSI-0 device
cd0: 16.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
cd1 at ata1 bus 0 target 1 lun 0
cd1: <PIONEER DVD-RW  DVR-105 1.33> Removable CD-ROM SCSI-0 device
cd1: 16.000MB/s transfers
cd1: Attempt to query device size failed: NOT READY, Medium not present
Mounting root from ufs:/dev/ad0s1a
WARNING: driver "vmmon" used unreserved major device number 200
vmmon: Module vmmon: registered with major=200 minor=0 tag=$Name: build-570 (3.2.x mvm) $
vmmon: Module vmmon: initialized
WARNING: /mnt was not properly dismounted
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=2, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)

muss ich denn nun sound_load="YES" unbedingt in der loader.conf
setzen bei 5.4

mfg
ACID25
 
Zuletzt bearbeitet:
Code: 
pci1: <multimedia, audio> at device 7.0 (no driver attached)

Das ist deine Sound-Karte. Bist du sicher, dass du auch wirklich den richtigen Soundtreiber hast? Probier doch mal

Code: 
kldload snd_driver

Damit werden alle Soundtreiber geladen. Falls nun ein Ton kommt kannst du mit

Code: 
cat /dev/sndstat

herausfinden, welcher Treiber nun benutzt wird.

Grüße
Styx
 
moinsen

ja ich weiß das erste posting war nicht korrekt ;)

aber ein kldload snd_driver bringt wieder nur das selbe ergebnis

Code: 
tuxi# kldload snd_driver
tuxi# cat /dev/sndstat
FreeBSD Audio Driver (newpcm)
Installed devices:

mmh bin echt ein wenig ratlos warum er den treiber jetzt nicht mehr nimmt :(
und der chip ist definitiv ein FM801

Mfg
ACID25
 
das ist zwar ein schuss ins blau, aber irgendwie fällt mir folgender eintrag in deiner dmesg auf:
...
WARNING: driver "vmmon" used unreserved major device number 200
....
Zum Vergrößern anklicken....

vielleicht blockiert der die nötigen resourcen?
wie gesagt schuss ins blaue!
 
Hi

das wäre ne möglichkeit obwohl unter 5.3 lief es auch so ;)
wie kann ich denn die device number ändern?

Mfg
ACID25
 
Du musst dich einloggen oder registrieren, um hier zu antworten.
Zurück
Oben