Also, hier nun die unter FreeBSD 5.2.1 funktionierende XF86Config:
Section "ServerFlags"
#Option "AllowMouseOpenFail"
#Option "noPM"
Option "BlankTime" "99999"
Option "StandbyTime" "99999"
Option "SuspendTime" "99999"
Option "OffTime" "99999"
EndSection
Section "Module"
Load "GLcore"
Load "dbe"
#Load "dri" - no longer needed, driver loads it automatically
Load "extmod"
Load "glx" # must have this unless DRI disabled by Option "DRI"
Load "pex5"
Load "record"
Load "xie"
Load "bitmap"
Load "freetype"
Load "speedo"
Load "type1"
# For XFree86 4.1, add the following here:
# Load "vbe"
# Load "int10"
EndSection
Section "InputDevice"
Identifier "Generic Keyboard"
Driver "keyboard"
Option "CoreKeyboard"
Option "XkbRules" "xfree86"
Option "XkbModel" "pc105"
Option "XkbLayout""de"
# Option "XkbVariant" "nodeadkeys"
EndSection
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/sysmouse"
Option "Protocol" "auto"
Option "Emulate3Buttons" "true"
Option "ZAxisMapping" "4 5"
Option "Buttons" "5"
EndSection
# MONITOR section
# ----------------------------------------------------------
# This section contains data for monitor configuration.
# The data in the Monitor section is only used for CRT1 (VGA),
# and will be ignored for CRT2 (unless CRT2 is a secondary VGA).
# If you only run with CRT2 (such as on laptops without an external
# monitor connected), you should place same sane values here anyway,
# in order to keep the X server from deleting modes from the list.
Section "Monitor"
Identifier "Generic|Generic LCD Panel"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
VertRefresh 50-75
HorizSync 30-90
EndSection
# ----------------------------------------------------------
# DEVICE section
# ----------------------------------------------------------
# This section contains configuration data of the video card.
Section "Device"
Driver "vesa"
Identifier "SiS 630"
VendorName "SiS"
BoardName "630"
# Option "HWCursor"
# Use hardware or software cursor ("HWCursor" / "SWCursor")
Option "HWcursor"
# Option "NoAccel"
# Setting this option will disable 2D/3D accellerators (and Xv).
#Option "NoAccel"
# Option "ForceCRT1"
# If CRT1 (=external VGA) monitor is used depends on whether the driver
# detects it during server start. If you want to override this
# automatic detection, set this option to either "true" (to enable
# CRT1) or "false" (to disable CRT1)
#Option"ForceCRT1" "true"
# Option "ForceCRT2Type":
# This option selects the CRT2 output device type and is only useful
# on systems containing a video bridge (such as most laptops).
# Available options are:
# "TV" (if TV connector present),
# "LCD" alias "DVI-D" (if LCD panel present),
# "VGA" alias "DVI-A" (secondary VGA; use this only if your machine
# has a secondary VGA connector or a DVI-I connector
# The VGA plug on your laptop is CRT1!)
# "NONE" (this will switch off CRT2).
# "COMPOSITE" (SiS video bridge only) Force TV to use cvbs connector
# "SVIDEO" (SiS video bridge only) Force TV to use SVHS connector
# "SCART" (SiS video bridge only) Force TV to use SCART connector
# "SVIDEO+COMPOSITE" (SiS video bridge only) for both
#Option "ForceCRT2Type" "NONE"
# Option "MaxXFBMem":
# Only useful on 300 series!
# YOU DON'T NEED THIS ON 315/550/65x/M650/661/740/741/Xabre/760
# This option limits the amount of memory X uses for its framebuffer.
# Its purpose is to avoid a clash between X and DRI/DRM/sisfb as regards
# memory management.
# The SiS kernel framebuffer driver (sisfb) is responsible for memory
# management for DRI. It will install a video memory heap at
# - 12 MB (=12288 KB) if more than 16MB of video RAM available,
# - 8 MB (=8192 KB) if between 8 an 16MB if video RAM available,
# - 4 MB (=4096 KB) if less than 8 MB of video RAM available.
# Other amounts can be specified with sisfb's "mem" parameter.
# If this option is set, X only uses the specified amount of memory for
# its screen and its off-screen buffers.
# Limiting X to use only a small part of RAM therefore avoids that
# the kernel framebuffer (and a DRI application using the sisfb's
# memory pool) overwrites X's screen and off-screen memory.
# When setting MaxXFBMem to "8192", memory will be used according
# to the following figure:
# 0-------8------16------24------32------40------48--------56-------64MB
# XXXXXXXX
# FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
# (X=memory used by X, F=memory used by sisfb and thus DRI)
# If DRI is disabled and the framebuffer driver is not loaded, this option
# can and should be left out.
Option "MaxXFBMem" "12288"
# Option "TVStandard"
# Can be "NTSC" or "PAL". On some machines with a 30x/B/LV bridge as well
# as on machines with a Chrontel 7019/7020, also
# "PALM" (for PAL-M) or "PALN" (PAL-N)
# Normally, this will be autodetected acoording to the BIOS setting.
#Option "TVStandard" "PAL"
# Option "XvOnCRT2"
# Only useful on machines with SiS315, 650 or 740 and only if both CRT1 and
# CRT2 are available and connected.
# Setting this to "TRUE" will show the Xv video overlay on CRT2, "FALSE" will
# show the overlay on CRT1.
#Option "XvOnCRT2" "true"
# Options for Chrontel TV encoders only ---------------
# Option "CHTVOvercan"
# Setting this to "TRUE" will use overscan modes (larger image on the TV)
# Normally this is autodetected according to the BIOS setting.
#Option "CHTVOverscan" "TRUE"
# Option "CHTVSuperOverscan"
# Not for Chrontel 701x TV encoders!
# Only useful if TV standard is PAL
# Setting this to "true" will force the driver to use a TV mode which is even
# larger than the normal overscan mode. This option overrules the CHTVOverscan
# option. Setting it to "FALSE" will make the driver to fall back on the
# normal overscan setting (BIOS selection or, if set, the CHTVOverscan setting)
#Option "CHTVSuperOverscan" "TRUE"
# Option "CHTVContrast"
# This option accepts numerical values from 0 to 15 and it adjust the contrast
# of the TV image.
#Option "CHTVContrast" "10"
# Options for SiS video bridges only --------------------
# Option "SISTVAntiFlicker"
# This option allows adjusting the bridge's anti flicker engine. It accepts
# "OFF", "LOW", "MED", "HIGH" and "ADAPTIVE"
#Option "SISTVAntiFlicker" "ADAPTIVE"
# Option "SISTVSaturation"
# This option allows tuning the color saturation of the TV image. It accepts
# values from 0 to 15.
#Option "SISTVSaturation" "15"
# Option "TVXPosOffset"
# Useful on machines with SiS6326+TV, Chrontel 700x TV encoder or SiS video
# bridge.
# This option allows adjusting the TV image's horizontal position. It accepts
# values from -32 to 32 (on the 6326 -16 to 16)
#Option "TVXPosOffset" "8"
# Option "TVYPosOffset"
# Like TVXPosOffset, but for vertical adjustments.
#Option "TVYPosOffset" "-3"
# Please see
http://www.winischhofer.net/linuxsisvga.shtml for more information
EndSection
# ----------------------------------------------------------
# SCREEN section
# ----------------------------------------------------------
# This section defines the available resulutions and depths.
# If you disable CRT2 (by setting ForceCRT2Type to "NONE"),
# you can use higher resolutions than the LCD panel supports.
Section "Screen"
Identifier "screen1"
Device "SiS 630"
Monitor "Generic|Generic LCD Panel"
DefaultDepth 16
SubSection "Display"
Depth 16
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1024x768" "800x600" "640x480"
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen "screen1"
InputDevice "Generic Keyboard"
InputDevice "Configured Mouse"
EndSection
# end of XF86Config
