Tach!
Ich hab hier zwei SAS-Platten, die eine spuckt folgendes in dmesg:
die andere:
Die Platten sind 'gebraucht', haben aber grad mal 200 Stunden runter.
Bei /dev/da3 lass ich grade mal ein 'camcontrol format da3' laufen, in der Hoffnung, dass es was bringt. Daher schätze ich auch, dass smart auslesen gerade nicht geht.
Info zum Controller (ist auf IT-Mode geflasht, weil wegen ZFS):
Mach ich dabei was falsch? Ich stell die Kiste gerade noch zusammen und teste, läuft noch nicht produktiv.
Ich hab hier zwei SAS-Platten, die eine spuckt folgendes in dmesg:
Code:
(da3:mps0:0:5:0): Descriptor 0x80: f7 01
(da3:mps0:0:5:0): Descriptor 0x81: 00 00 01 00 00 00
(da3:mps0:0:5:0): Retrying command (per sense data)
(da3:mps0:0:5:0): READ(6). CDB: 08 00 00 00 01 00
(da3:mps0:0:5:0): CAM status: SCSI Status Error
(da3:mps0:0:5:0): SCSI status: Check Condition
(da3:mps0:0:5:0): SCSI sense: MEDIUM ERROR asc:31,0 (Medium format corrupted)
(da3:mps0:0:5:0):
(da3:mps0:0:5:0): Field Replaceable Unit: 0
(da3:mps0:0:5:0): Command Specific Info: 0
(da3:mps0:0:5:0):
(da3:mps0:0:5:0): Descriptor 0x80: f7 01
(da3:mps0:0:5:0): Descriptor 0x81: 00 00 01 00 00 00
(da3:mps0:0:5:0): Error 5, Retries exhausted
die andere:
Code:
(da0:mps0:0:1:0): Descriptor 0x80: f8 21
(da0:mps0:0:1:0): Descriptor 0x81: 00 00 00 00 00 00
(da0:mps0:0:1:0): Error 22, Unretryable error
(da0:mps0:0:1:0): READ(10). CDB: 28 00 e8 e0 88 af 00 00 01 00
(da0:mps0:0:1:0): CAM status: SCSI Status Error
(da0:mps0:0:1:0): SCSI status: Check Condition
(da0:mps0:0:1:0): SCSI sense: ILLEGAL REQUEST asc:20,0 (Invalid command operation code)
(da0:mps0:0:1:0):
(da0:mps0:0:1:0): Field Replaceable Unit: 0
(da0:mps0:0:1:0): Command Specific Info: 0
(da0:mps0:0:1:0):
(da0:mps0:0:1:0): Descriptor 0x80: f8 21
(da0:mps0:0:1:0): Descriptor 0x81: 00 00 00 00 00 00
(da0:mps0:0:1:0): Error 22, Unretryable error
Die Platten sind 'gebraucht', haben aber grad mal 200 Stunden runter.
Code:
smartctl -a /dev/da3
smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.1-RELEASE amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: HITACHI
Product: HUS723020ALS641
Revision: MS06
Compliance: SPC-4
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Logical Unit id: 0x5000cca01b8ef204
Serial number: YFJJM1YD
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Tue Feb 20 18:48:31 2018 CET
device is NOT READY (e.g. spun down, busy)
A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.
Bei /dev/da3 lass ich grade mal ein 'camcontrol format da3' laufen, in der Hoffnung, dass es was bringt. Daher schätze ich auch, dass smart auslesen gerade nicht geht.
Code:
smartctl -a /dev/da0
smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.1-RELEASE amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: HITACHI
Product: HUS723020ALS641
Revision: MS06
Compliance: SPC-4
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Logical block size: 512 bytes
Formatted with type 2 protection
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Logical Unit id: 0x5000cca01b8e7158
Serial number: YFJJAH9D
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Tue Feb 20 18:47:52 2018 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Current Drive Temperature: 29 C
Drive Trip Temperature: 55 C
Manufactured in week 48 of year 2012
Specified cycle count over device lifetime: 50000
Accumulated start-stop cycles: 19
Specified load-unload count over device lifetime: 600000
Accumulated load-unload cycles: 23
Elements in grown defect list: 0
Vendor (Seagate) cache information
Blocks sent to initiator = 994519810048
Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 0 0 0 0 36 25.988 0
write: 0 0 0 0 1591 20.014 0
verify: 0 0 0 0 145 77.352 0
Non-medium error count: 0
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Background short Completed - 200 - [- - -]
Long (extended) Self Test duration: 6 seconds [0.1 minutes]
Info zum Controller (ist auf IT-Mode geflasht, weil wegen ZFS):
Code:
mps0 Adapter:
Board Name: H220
Board Assembly: H3-25278-05D
Chip Name: LSISAS2308
Chip Revision: ALL
BIOS Revision: 7.39.02.00
Firmware Revision: 20.00.07.00
Integrated RAID: no
Mach ich dabei was falsch? Ich stell die Kiste gerade noch zusammen und teste, läuft noch nicht produktiv.