Aeli schrieb:
Hi da
Was für ein bios- Was für ein Rechner- was für ein SCSI- Controller- was für Platten?
sonst führt das zu nix.
gruss
Motherboard:
Asus P2B - F; Bios Award 1013A
PIII 450
SCSI-Controller:
Adaptec AAA 131 Raid-Controller
Platten: da1: 8 GB IBM DDRS-39130D
da0: 17 GB SEAGATE ST318203 W
ad0: 78 GB MAXTOR
Hier mein dmesg
ACPI debug layer 0x0 debug level 0x0
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.2.1-RELEASE #1: Fri Aug 20 23:44:03 CEST 2004
root@biber.labers:/usr/obj/usr/src/sys/BIBER.5.2.1
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a1f000.
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Pentium III/Pentium III Xeon/Celeron (451.02-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x673 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 335532032 (319 MB)
avail memory = 316284928 (301 MB)
Pentium Pro MTRR support enabled
VESA: v2.0, 4096k memory, flags:0x1, mode table:0xc09521e2 (1000022)
VESA: Matrox Graphics Inc.
acpi0: <ASUS P2B-F > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 7 entries at 0xc00f0d10
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_cpu0: <CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib0: slot 4 INTD is routed to irq 9
pcib0: slot 9 INTA is routed to irq 9
pcib0: slot 10 INTA is routed to irq 9
pcib0: slot 11 INTA is routed to irq 10
pcib0: slot 12 INTA is routed to irq 11
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xe4000000-0xe7ffffff at device 0.0 on pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <PCI-ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port 0xd800-0xd80f at device 4.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd400-0xd41f irq 9 at device 4.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, PCI-unknown> at device 4.3 (no driver attached)
vr0: <VIA VT3043 Rhine I 10/100BaseTX> port 0xd000-0xd07f mem 0xe1000000-0xe100007f irq 9 at device 9.0 on pci0
vr0: Ethernet address: 00:80:c8:fb:4f:df
miibus0: <MII bus> on vr0
amphy0: <Am79C873 10/100 media interface> on miibus0
amphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ahc0: <Adaptec 2902/04/10/15/20C/30C SCSI adapter> port 0xb800-0xb8ff mem 0xe0800000-0xe0800fff irq 9 at device 10.0 on pci0
ahc0: Host Adapter Bios disabled. Using default SCSI device parameters
aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs
pci0: <display, VGA> at device 11.0 (no driver attached)
fxp0: <Intel 82559 Pro/100 Ethernet> port 0xb400-0xb43f mem 0xde800000-0xde8fffff,0xdf000000-0xdf000fff irq 11 at device 12.0 on pci0
fxp0: Ethernet address 00:d0:b7:90:2d:d2
miibus1: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus1
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib2: <PCI-PCI bridge> at device 13.0 on pci0
pci2: <PCI bus> on pcib2
pcib0: slot 13 INTA is routed to irq 9
pcib2: slot 0 INTA is routed to irq 9
pcib0: slot 13 INTA is routed to irq 9
pcib2: slot 4 INTA is routed to irq 9
ahc1: <Adaptec aic7815 RAID memory controller> port 0xa800-0xa8ff mem 0xe2000000-0xe23fffff,0xde000000-0xde000fff irq 9 at device 0.0 on pci2
RAID functionality unsupported
device_probe_and_attach: ahc1 attach returned 6
ahc1: <Adaptec AAA-131 Ultra2 RAID adapter> port 0xa400-0xa4ff mem 0xdd800000-0xdd800fff irq 9 at device 4.0 on pci2
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
orm0: <Option ROMs> at iomem 0xcc000-0xd37ff,0xc8000-0xc8fff,0xc0000-0xc7fff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 451024642 Hz quality 800
Timecounters tick every 10.000 msec
GEOM: create disk ad0 dp=0xc3445c60
ad0: 78167MB <Maxtor 4R080L0> [158816/16/63] at ata0-master UDMA33
acd0: CDROM <CD-ROM CDU611-Q> at ata0-slave WDMA2
Waiting 3 seconds for SCSI devices to settle
GEOM: create disk da0 dp=0xc34f0c50
GEOM: create disk da1 dp=0xc3441c50
da0 at ahc1 bus 0 target 0 lun 0
da0: <SEAGATE ST318203LW 0002> Fixed Direct Access SCSI-2 device
da0: 80.000MB/s transfers (40.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da0: 17366MB (35566480 512 byte sectors: 255H 63S/T 2213C)
da1 at ahc1 bus 0 target 3 lun 0
da1: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device
da1: 10.000MB/s transfers (5.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da1: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
Mounting root from ufs:/dev/da0s1a
Loading configuration files.
Entropy harvesting:
interrupts
ethernet
point_to_point
.
swapon: adding /dev/da0s1b as swap device
Starting file system checks:
/dev/da0s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/da0s1a: clean, 94473 free (569 frags, 11738 blocks, 0.4% fragmentation)
/dev/da0s1d: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/da0s1d: clean, 394678 free (46 frags, 49329 blocks, 0.0% fragmentation)
/dev/da0s1e: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/da0s1e: clean, 392704 free (472 frags, 49029 blocks, 0.1% fragmentation)
/dev/ad0s1e: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1e: clean, 5426538 free (202 frags, 678292 blocks, 0.0% fragmentation)
/dev/ad0s1f: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1f: clean, 12432443 free (1123 frags, 1553915 blocks, 0.0% fragmentation)
/dev/da0s1f: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/da0s1f: clean, 6299089 free (33033 frags, 783257 blocks, 0.5% fragmentation)
kern.ipc.shm_allow_removed:
0
->
1
Setting hostname: biber.labers.
fxp0: Microcode loaded, int_delay: 1000 usec bundle_max: 6
fxp0: Microcode loaded, int_delay: 1000 usec bundle_max: 6
vr0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255
inet6 fe80::280:c8ff:fefb:4fdf%vr0 prefixlen 64 tentative scopeid 0x1
ether 00:80:c8:fb:4f:df
media: Ethernet autoselect (none)
status: no carrier
fxp0: flags=9843<UP,BROADCAST,RUNNING,SIMPLEX,LINK0,MULTICAST> mtu 1500
inet 192.168.0.33 netmask 0xffffff00 broadcast 192.168.0.255
inet6 fe80::2d0:b7ff:fe90:2dd2%fxp0 prefixlen 64 tentative scopeid 0x2
ether 00:d0:b7:90:2d:d2
media: Ethernet autoselect (none)
status: no carrier
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
ipfw2 initialized, divert disabled, rule-based forwarding enabled, default to deny, logging disabled
Flushed all rules.
00100 allow ip from any to any via lo0
00200 deny ip from any to 127.0.0.0/8
00300 deny ip from 127.0.0.0/8 to any
65000 allow ip from any to any
Firewall rules loaded, starting divert daemons:
.
net.inet.ip.fw.enable:
1
->
1
add net default: gateway 192.168.0.254
Additional routing options:
.
hw.bus.devctl_disable:
0
->
1
Mounting NFS file systems:
.
Starting syslogd.
Aug 21 13:42:42 biber syslogd: kernel boot file is /boot/kernel/kernel
ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/X11R6/lib /usr/local/lib
a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout /usr/X11R6/lib/aout /usr/local/lib/aout
Starting local daemons:
.
Configuring syscons:
keymap
keyrate
font8x16
font8x14
font8x8
blanktime
screensaver
allscreens
.
Starting sshd.
Initial i386 initialization:
.
Additional ABI support:
linux
.
Starting cron.
Local package initialization:
ahc2: <Adaptec aic7815 RAID memory controller> port 0xa800-0xa8ff mem 0xe2000000-0xe23fffff,0xde000000-0xde000fff irq 9 at device 0.0 on pci2
RAID functionality unsupported
device_probe_and_attach: ahc2 attach returned 6
ltmdm
.
Additional TCP options:
.
Starting moused:
.
Starting background file system checks in 60 seconds.
Der Controller hat ein BIOS, d.h. eigentlich müssten die Platten ja bootfähig sein oder ?
