Problem smartmontools install

Voltron

Stinker
Hi Leute,

hab versucht auf meine fbsd 6.1 die smartmontools-5.36 zu installen weil ich so ne Meldung seit kurzem bekomme

g_vfs_done():twed0s1f.bde[WRITE(offset=277812690944, length=16384)]error = 5

Das sind 2 Seagate 320 sata 2 Platten an nem 3ware 7006-2 Sata Controller.
Ärgerlich da 2 neue Platten.

Ok mein Problem ist das das ./configure durch läuft aber er beim make dann mit diesem Fehler hier stehen bleibt.

make: don't know how to make smartd.conf.5. Stop
*** Error code 1

Stop in /root/smartmontools-5.36.
*** Error code 1

Stop in /root/smartmontools-5.36.

Damit kann ich aber leider nix anfangen, kann mir da einer von euch weiter helfen??

Greetz

Voltron
 
Habs gestern noch sauber aus den Ports installiert.

Hast ja zum Glück noch Garantie, kannst schonmal anfangen einzupacken :)
 
@Maledictus
du hast das zauberwort geliefert.

@Voltron
Code:
Stop in /root/smartmontools-5.36.
*** Error code 1

errorcode in /root/.. ?

versuchst du die übersetzung per ports oder hast du was runtergeladen und versuchst es dann ?

wir lesen uns
ZbZ
 
smartmontools - eine Einführung

Hallo,

bisher hatte ich mich für sysutils/smartmontools
irgendwie zu blöd angestellt,
aber ich habe gerade eine deutschsprachige Einleitung für
die smartmontools auf Deutsch -allerdings für Linux- entdeckt.

Also bitte nicht blind das Linux Device abtippen sondern bitte daran denken
das z.B. die erste ATA Festplatte so abgerufen wird:
Code:
/usr/local/sbin/smartctl -a /dev/ad0

und die erste SCSI Festplatte so
Code:
/usr/local/sbin/smartctl -a /dev/da0

Einen kurzen Überblick über die smartctl Optionen gibts mit:
Code:
/usr/local/sbin/smartctl -h

Die deutschprachige Linuxlastige Einführung
über die smartmontools gibts hier:
http://www.tweakpc.de/forum/tutorials/29413-eine-einfuehrung-in-smart-smartmontools-linux.html



Natürlich gibts auch noch die Manuals: ;)
Code:
man smartd
man smartd.conf
man smartctl


Gruß, Fusselbär
 
Zuletzt bearbeitet:
Ahhhh i hatte es runter geladen, ab und an in den ports nachzuschaun is doch sinnvoll :rolleyes:

Ich hoff nich das ich da was eintütln muss, der Controller zeigt keine Errors, nur des bsd selbst und da auch nur bei der bde partition, evtl verrechnet beim anlegen.

Bei beiden Platten zeigt er das hier an

SMART Error Log Version: 1
No Errors Logged

Da kann ma doch von ausgehen das die Platten keinen Fehler haben oder?

Hier nochmal die komplette Ausgabe von smartmon

Platte 0

Code:
smartctl version 5.36 [i386-portbld-freebsd6.1] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model:     ST3320620AS
Serial Number:    5QF00LJP
Firmware Version: 3.AAC
User Capacity:    320,072,933,376 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   7
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Sun Aug 27 17:26:34 2006 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		 ( 430) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 115) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   117   100   006    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0003   092   092   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       6
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   074   060   030    Pre-fail  Always       -       28467377
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       268
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       12
187 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       0
189 Unknown_Attribute       0x003a   100   100   000    Old_age   Always       -       0
190 Unknown_Attribute       0x0022   065   047   045    Old_age   Always       -       740229155
194 Temperature_Celsius     0x0022   035   053   000    Old_age   Always       -       35 (Lifetime Min/Max 0/31)
195 Hardware_ECC_Recovered  0x001a   069   066   000    Old_age   Always       -       2574751
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age   Offline      -       0
202 TA_Increase_Count       0x0032   100   253   000    Old_age   Always       -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.


und Platte 1

Code:
smartctl version 5.36 [i386-portbld-freebsd6.1] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model:     ST3320620AS
Serial Number:    5QF00LK8
Firmware Version: 3.AAC
User Capacity:    320,072,933,376 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   7
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Sun Aug 27 17:26:55 2006 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		 ( 430) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 115) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   117   100   006    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0003   092   092   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       6
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   072   060   030    Pre-fail  Always       -       17223245
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       236
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       12
187 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       0
189 Unknown_Attribute       0x003a   100   100   000    Old_age   Always       -       0
190 Unknown_Attribute       0x0022   068   045   045    Old_age   Always   In_the_past 639500320
194 Temperature_Celsius     0x0022   032   055   000    Old_age   Always       -       32 (Lifetime Min/Max 0/30)
195 Hardware_ECC_Recovered  0x001a   070   066   000    Old_age   Always       -       184214009
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age   Offline      -       0
202 TA_Increase_Count       0x0032   100   253   000    Old_age   Always       -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
 
Zuletzt bearbeitet:
Nein, kannst du nicht.

Mir ist die Tage ne Platte verstorben, die sogar nach
smartctl -t long
noch keine Fehler hatte. Das solltest du auch mal ausführen. Und den Anweisungen auf dem Bildschirm folgen.

Meine war auch Seagate, auch erst einige hundert Betriebsstunden :(
 
Hi Voltron,

nachdem twedxxx vom 3ware controller erzeugtes logisches Volumes ist, kann dieses eigentlich keinen vfs error erzeugen.

Code:
g_vfs_done():twed0s1f.bde[WRITE(offset=277812690944, length=16384)]error = 5

Da steckt eine GBDE Verschlüsselung drin. Wenn diese bei der Erstellung mit Hilfe eines angepassten Templates erstellt worden ist, könnte ggf. bei der Größenberechnung nen Fehler unterlaufen sein, der dem GBDE ne größere Dimension zeigt, als tatsächlich auf dem logischen Vol verfügbar.

Müßte jetzt in den GEOM code von GBDE nochmal nachsehen, aber denke das BDE beim überziehen nen geom error zurückmelden würde.

Daher, wohl oder übel nochmal alles rauskopieren, BDE neu anlegen und am besten gleich mit der "flush with random" (oder ähnlich) versehen.

Grüße,

Yze
 
Zurück
Oben