amd64 langsam

r_friemer

Active Member
Hallo!

ich möchte auf einem Rechner mit Intel(R) Core(TM)2 CPU 6420 @ 2.13GHz CPU FreeBSD amd64 installieren. Eigentlich ist dies kein Problem, nur dass die Geschwindigkeit während der Installation und danach unheimlich langsam ist. Als ob noch die Handbremse angezogen ist. :-(

Das Mainboard hat einen 82801 H Chipsatz (ICH 8 Family ?), 2 SATA-Platten und ein SATA-DVD-Brenner. Die Grafik-Karte ist eine Intel 965Q

Wenn ich eine i386-Installation mache geht es schneller als mit der amd64-Version. Der Nachteil ist nun der, dass ich nur 32-Bit nutze und von den 6GB nur 3GB zu Verfügung habe.

Parallel habe ich ein Linux (OpenSUSE 11.4, 64-Bit) auf einer zweite Platte installiert und dieses geht auch einwandfrei in der 64bit Version.

Kann mir jemand helfen, das Problem mit dem gebremsten amd64 zu lösen?

Vielen Dank

r_friemer
 
Ist die CPU langsam oder die Festplatten? Du musst schon einige Fakten präsentieren, sonst kann man da nicht viel helfen.

Hast Du schon mal geguckt ob irgendein Programm oder Kerneltreiber die CPU frisst?

Code:
systat
systat -iostat

Zeigen die beiden Kommandos was besonderes?
 
Code:
vmstat -i
ist auch immer schön um amoklaufende IRQ zu finden
 
Hallo jetzt bin ich wieder da!

Ich habe nun systat und systat -iostat ausprobiert. Es zeigt fast 100% idle an. Auch die iostat zeigt fast idle bei der CPU und dem Controller an.

Heißt das nun das der Rechner eigentlich optimal an?

Hier habe ich noch das dmesg -a

Copyright (c) 1992-2011 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.2-RELEASE #0: Fri Feb 18 02:24:46 UTC 2011
root@almeida.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC i386
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (3006.83-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf33 Family = f Model = 3 Stepping = 3
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x41d<SSE3,DTES64,MON,DS_CPL,CNXT-ID>
TSC: P-state invariant
real memory = 3221225472 (3072 MB)
avail memory = 3141386240 (2995 MB)
ACPI APIC Table: <A M I OEMAPIC >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 1 core(s) x 2 HTT threads
cpu0 (BSP): APIC ID: 0
cpu1 (AP/HT): APIC ID: 1
ioapic0: Changing APIC ID to 2
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <A M I OEMRSDT> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, bfef0000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82865 host to AGP bridge> on hostb0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xc000-0xc0ff mem 0xf0000000-0xf7ffffff,0xfd5f0000-0xfd5fffff irq 16 at device 0.0 on pci1
uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xef00-0xef1f irq 16 at device 29.0 on pci0
uhci0: [ITHREAD]
uhci0: LegSup = 0x2f00
usbus0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xef20-0xef3f irq 19 at device 29.1 on pci0
uhci1: [ITHREAD]
uhci1: LegSup = 0x2f00
usbus1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xef40-0xef5f irq 18 at device 29.2 on pci0
uhci2: [ITHREAD]
uhci2: LegSup = 0x2f00
usbus2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0xef80-0xef9f irq 16 at device 29.3 on pci0
uhci3: [ITHREAD]
uhci3: LegSup = 0x2f00
usbus3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
ehci0: <Intel 82801EB/R (ICH5) USB 2.0 controller> mem 0xfe7ffc00-0xfe7fffff irq 23 at device 29.7 on pci0
ehci0: [ITHREAD]
usbus4: EHCI version 1.0
usbus4: <Intel 82801EB/R (ICH5) USB 2.0 controller> on ehci0
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
skc0: <Marvell Gigabit Ethernet> port 0xd800-0xd8ff mem 0xfe6fc000-0xfe6fffff irq 22 at device 5.0 on pci2
skc0: Marvell Yukon Lite Gigabit Ethernet rev. A3(0x7)
sk0: <Marvell Semiconductor, Inc. Yukon> on skc0
sk0: Ethernet address: 00:0e:a6:ba:74:47
miibus0: <MII bus> on sk0
e1000phy0: <Marvell 88E1011 Gigabit PHY> PHY 0 on miibus0
e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
skc0: [ITHREAD]
twe0: <3ware Storage Controller. Driver version 1.50.01.002> port 0xdfa0-0xdfaf mem 0xfe6fbc00-0xfe6fbc0f,0xfd800000-0xfdffffff irq 22 at device 10.0 on pci2
twe0: [GIANT-LOCKED]
twe0: [ITHREAD]
twe0: 2 ports, Firmware FE8S 1.05.00.068, BIOS BE7X 1.08.00.048
re0: <RealTek 8169/8169S/8169SB(L)/8110S/8110SB(L) Gigabit Ethernet> port 0xd400-0xd4ff mem 0xfe6fb800-0xfe6fb8ff irq 20 at device 12.0 on pci2
re0: Chip rev. 0x04000000
re0: MAC rev. 0x00000000
miibus1: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus1
rgephy0: 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
re0: Ethernet address: 00:18:4d:6f:49:6a
re0: [FILTER]
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH5 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <Power Button> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcbfff,0xcc000-0xccfff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
ppc0: parallel port not found.
p4tcc0: <CPU Frequency Thermal Control> on cpu0
p4tcc1: <CPU Frequency Thermal Control> on cpu1
Timecounters tick every 1.000 msec
vboxdrv: fAsync=0 offMin=0xddb offMax=0x1588
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
acd0: DVDROM <LITE-ON DVD SOHD-167T/9S14> at ata0-master UDMA33
twed0: <Unit 0, TwinStor, Normal> on twe0
twed0: 239371MB (490232704 sectors)
SMP: AP CPU #1 Launched!
ugen1.1: <Intel> at usbus1ugen0.1: <Intel> at usbus0

uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen2.1: <Intel> at usbus2ugen3.1: <Intel> at usbus3

uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
Root mount waiting for: usbus4 usbus3 usbus2 usbus1 usbus0
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
Root mount waiting for: usbus4
Root mount waiting for: usbus4
uhub4: 8 ports with 8 removable, self powered
Trying to mount root from ufs:/dev/twed0s1a
Setting hostuuid: 00020003-0004-0005-0006-000700080009.
Setting hostid: 0x81f4ec68.
Entropy harvesting:
interrupts
ethernet
point_to_point
kickstart
.
Starting file system checks:
/dev/twed0s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/twed0s1a: clean, 3701320 free (9368 frags, 461494 blocks, 0.2% fragmentation)
/dev/twed0s1e: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/twed0s1e: clean, 90851376 free (23232 frags, 11353518 blocks, 0.0% fragmentation)
/dev/twed0s1d: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/twed0s1d: clean, 9273081 free (32737 frags, 1155043 blocks, 0.3% fragmentation)
Mounting local file systems:
.
Setting hostname: annamirl.muc.stockfood.de
.
Starting Network: lo0 re0.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=3<RXCSUM,TXCSUM>
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
nd6 options=3<PERFORMNUD,ACCEPT_RTADV>
re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=389b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC>
ether 00:18:4d:6f:49:6a
inet 192.168.7.88 netmask 0xffffff00 broadcast 192.168.7.255
inet6 fe80::218:4dff:fe6f:496a%re0 prefixlen 64 tentative scopeid 0x2
nd6 options=3<PERFORMNUD,ACCEPT_RTADV>
media: Ethernet autoselect (none)
status: no carrier
add net default: gateway 192.168.7.1
add net ::ffff:0.0.0.0: gateway ::1
add net ::0.0.0.0: gateway ::1
net.inet6.ip6.forwarding:
0
->
0

net.inet6.ip6.accept_rtadv:
0
->
1

add net fe80::: gateway ::1
add net ff02::: gateway ::1
add net default: gateway fe80::%re0
IPv4 mapped IPv6 address support=YES
Starting devd.
Mounting SMB file systems:
netsmb_dev: loaded
.
ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/lib/compat/pkg /usr/local/lib /usr/local/lib/compat/pkg /usr/local/lib/gcc44 /usr/local/lib/gcc45 /usr/local/lib/graphviz /usr/local/lib/mlt /usr/local/lib/pth /usr/local/lib/qt4 /usr/local/lib/virtualbox
a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout
Creating and/or trimming log files
.
Starting syslogd.
Clearing /tmp (X related).
Updating motd:
.
Starting ntpd.
Removing stale Samba tdb files:
.
.
.
.
.
.
.
.
done
Starting nmbd.
Starting smbd.
Starting musicpd.
Starting sshd.
Configuring syscons:
keymap
blanktime
.
-bd is not supported by sSMTP
sendmail: Mail queue is empty
Starting cron.
Starting background file system checks in 60 seconds.

Mon Jul 4 13:55:03 CEST 2011
Jul 22 21:17:30 annamirl su: BAD SU robert to root on /dev/pts/0
Jul 22 21:17:40 annamirl su: robert to root on /dev/pts/0
Jul 22 21:17:59 annamirl su: robert to root on /dev/pts/2
Jul 22 21:18:37 annamirl su: robert to root on /dev/pts/0
Jul 22 21:28:59 annamirl su: robert to root on /dev/pts/0

Interressant ist auch, dass er "nur" 3GB findet, anstatt der 6GB.

Hat jemand noch eine Idee? Soll ich noch etwas auswerten?

Grüße

r_friemer
 
Also du nutzt i386, darum nur 3GBytes
Copyright (c) 1992-2011 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.2-RELEASE #0: Fri Feb 18 02:24:46 UTC 2011
root@almeida.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC i386

Kann es sein, dass dann auch die i386 Version langsam ist?

Hängen deine Platten an einem 3ware Controller (twed0)? Ausgehend vom ersten Post gehe ich eher von den SATA-Anschlüssen auf dem Mainboard aus. Was stimmt jetzt?

mousaka
 
Sorry,

mousaka, danke für den Tipp. Das war das dmesg von der falschen Maschine. :eek:

Peinlich. :ugly:

Das ist das dmesg -a der Maschine, die ich meine:

Copyright (c) 1992-2011 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.2-RELEASE #0: Thu Feb 17 02:41:51 UTC 2011
root@mason.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC amd64
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM)2 CPU 6420 @ 2.13GHz (2139.74-MHz K8-class CPU)
Origin = "GenuineIntel" Id = 0x6f6 Family = 6 Model = f Stepping = 6
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xe3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM>
AMD Features=0x20100800<SYSCALL,NX,LM>
AMD Features2=0x1<LAHF>
TSC: P-state invariant
real memory = 6442450944 (6144 MB)
avail memory = 6099017728 (5816 MB)
ACPI APIC Table: <INTEL DQ965GF >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0: Changing APIC ID to 2
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <INTEL DQ965GF> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0x2410-0x2417 mem 0xe0200000-0xe02fffff,0xd0000000-0xdfffffff irq 16 at device 2.0 on pci0
agp0: <Intel Q965 SVGA controller> on vgapci0
agp0: detected 7676k stolen memory
agp0: aperture size is 256M
pci0: <simple comms> at device 3.0 (no driver attached)
em0: <Intel(R) PRO/1000 Network Connection 7.1.9> port 0x20e0-0x20ff mem 0xe0300000-0xe031ffff,0xe0324000-0xe0324fff irq 20 at device 25.0 on pci0
em0: Using an MSI interrupt
em0: [FILTER]
em0: Ethernet address: 00:19:d1:9f:ab:77
uhci0: <Intel 82801H (ICH8) USB controller USB-D> port 0x20c0-0x20df irq 16 at device 26.0 on pci0
uhci0: [ITHREAD]
uhci0: LegSup = 0x2f00
usbus0: <Intel 82801H (ICH8) USB controller USB-D> on uhci0
uhci1: <Intel 82801H (ICH8) USB controller USB-E> port 0x20a0-0x20bf irq 21 at device 26.1 on pci0
uhci1: [ITHREAD]
uhci1: LegSup = 0x2f00
usbus1: <Intel 82801H (ICH8) USB controller USB-E> on uhci1
ehci0: <Intel 82801H (ICH8) USB 2.0 controller USB2-B> mem 0xe0325c00-0xe0325fff irq 18 at device 26.7 on pci0
ehci0: [ITHREAD]
usbus2: EHCI version 1.0
usbus2: <Intel 82801H (ICH8) USB 2.0 controller USB2-B> on ehci0
pci0: <multimedia, HDA> at device 27.0 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> at device 28.1 on pci0
pci2: <ACPI PCI bus> on pcib2
atapci0: <Marvell 88SX6101 UDMA133 controller> port 0x1018-0x101f,0x1024-0x1027,0x1010-0x1017,0x1020-0x1023,0x1000-0x100f mem 0xe0100000-0xe01001ff irq 17 at device 0.0 on pci2
atapci0: [ITHREAD]
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
pcib3: <ACPI PCI-PCI bridge> at device 28.2 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> at device 28.3 on pci0
pci4: <ACPI PCI bus> on pcib4
pcib5: <ACPI PCI-PCI bridge> at device 28.4 on pci0
pci5: <ACPI PCI bus> on pcib5
uhci2: <Intel 82801H (ICH8) USB controller USB-A> port 0x2080-0x209f irq 23 at device 29.0 on pci0
uhci2: [ITHREAD]
uhci2: LegSup = 0x2f00
usbus3: <Intel 82801H (ICH8) USB controller USB-A> on uhci2
uhci3: <Intel 82801H (ICH8) USB controller USB-B> port 0x2060-0x207f irq 19 at device 29.1 on pci0
uhci3: [ITHREAD]
uhci3: LegSup = 0x2f00
usbus4: <Intel 82801H (ICH8) USB controller USB-B> on uhci3
uhci4: <Intel 82801H (ICH8) USB controller USB-C> port 0x2040-0x205f irq 18 at device 29.2 on pci0
uhci4: [ITHREAD]
uhci4: LegSup = 0x2f00
usbus5: <Intel 82801H (ICH8) USB controller USB-C> on uhci4
ehci1: <Intel 82801H (ICH8) USB 2.0 controller USB2-A> mem 0xe0325800-0xe0325bff irq 23 at device 29.7 on pci0
ehci1: [ITHREAD]
usbus6: EHCI version 1.0
usbus6: <Intel 82801H (ICH8) USB 2.0 controller USB2-A> on ehci1
pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci6: <ACPI PCI bus> on pcib6
fwohci0: <Texas Instruments TSB43AB22/A> mem 0xe0004000-0xe00047ff,0xe0000000-0xe0003fff irq 19 at device 3.0 on pci6
fwohci0: [ITHREAD]
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:90:27:00:01:d1:4b:3b
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0xce6fc000
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:90:27:d1:4b:3b
fwe0: Ethernet address: 02:90:27:d1:4b:3b
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:90:27:00:01:d1:4b:3b @ 0xfffe00000000, S400, maxrec 2048
fwohci0: Initiate bus reset
fwohci0: fwohci_intr_core: BUS reset
fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, CYCLEMASTER mode
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <Intel ICH8 SATA300 controller> port 0x2408-0x240f,0x241c-0x241f,0x2400-0x2407,0x2418-0x241b,0x2020-0x203f mem 0xe0325000-0xe03257ff irq 19 at device 31.2 on pci0
atapci1: [ITHREAD]
atapci1: AHCI called from vendor specific driver
atapci1: AHCI v1.10 controller with 6 3Gbps ports, PM not supported
ata3: <ATA channel 0> on atapci1
ata3: [ITHREAD]
ata4: <ATA channel 1> on atapci1
ata4: [ITHREAD]
ata5: <ATA channel 2> on atapci1
ata5: [ITHREAD]
ata6: <ATA channel 3> on atapci1
ata6: [ITHREAD]
ata7: <ATA channel 4> on atapci1
ata7: [ITHREAD]
ata8: <ATA channel 5> on atapci1
ata8: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atrtc0: <AT realtime clock> port 0x70-0x71,0x74-0x77 irq 8 on acpi0
orm0: <ISA Option ROM> at iomem 0xcb800-0xcd7ff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
ppc0: cannot reserve I/O port range
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
RTC BIOS diagnostic error 80<clock_battery>
Timecounters tick every 1.000 msec
firewire0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
firewire0: bus manager 0
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 480Mbps High Speed USB v2.0
ad6: 381554MB <Seagate ST3400633AS 3.AAE> at ata3-master UDMA100 SATA 3Gb/s
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <Intel> at usbus5
uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
ugen6.1: <Intel> at usbus6
uhub6: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus6
ad10: 152627MB <Seagate ST3160815AS 3.AAC> at ata5-master UDMA100 SATA 3Gb/s
acd0: DVDR <Optiarc DVD RW AD-7173S/1-00> at ata6-master UDMA66 SATA 1.5Gb/s
SMP: AP CPU #1 Launched!
Root mount waiting for: usbus6 usbus5 usbus4 usbus3 usbus2 usbus1 usbus0
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
Root mount waiting for: usbus6 usbus2
uhub2: 4 ports with 4 removable, self powered
Root mount waiting for: usbus6 usbus2
uhub6: 6 ports with 6 removable, self powered
ugen2.2: <vendor 0x0471> at usbus2
Trying to mount root from ufs:/dev/ad10s1a
Setting hostuuid: 189a72f0-43e1-11dc-a7d5-000ea68f7399.
Setting hostid: 0x0847b249.
ugen3.2: <vendor 0x046a> at usbus3
ukbd0: <vendor 0x046a product 0x0023, class 0/0, rev 2.00/0.32, addr 2> on usbus3
kbd2 at ukbd0
uhid0: <vendor 0x046a product 0x0023, class 0/0, rev 2.00/0.32, addr 2> on usbus3
Entropy harvesting:
interrupts
ethernet
point_to_point
ugen3.3: <Logitech> at usbus3
ums0: <Logitech USB Optical Mouse, class 0/0, rev 2.00/43.01, addr 3> on usbus3
ums0: 3 buttons and [XYZ] coordinates ID=0
kickstart
.
Starting file system checks:
/dev/ad10s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad10s1a: clean, 11846732 free (14068 frags, 1479083 blocks, 0.1% fragmentation)
/dev/ad10s1d: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad10s1d: clean, 59918247 free (23 frags, 7489778 blocks, 0.0% fragmentation)
Mounting local file systems:
.
Setting hostname: sto31.muc.stockfood.de
.
Starting Network: lo0 em0.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=3<RXCSUM,TXCSUM>
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
nd6 options=3<PERFORMNUD,ACCEPT_RTADV>
em0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=219b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,WOL_MAGIC>
ether 00:19:d1:9f:ab:77
inet6 fe80::219:d1ff:fe9f:ab77%em0 prefixlen 64 tentative scopeid 0x1
nd6 options=3<PERFORMNUD,ACCEPT_RTADV>
media: Ethernet autoselect
status: no carrier
add net ::ffff:0.0.0.0: gateway ::1
add net ::0.0.0.0: gateway ::1
net.inet6.ip6.forwarding:
0
->
0

fwe0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8<VLAN_MTU>
ch 1 dma -1
fwip0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=3<RXCSUM,TXCSUM>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
net.inet6.ip6.accept_rtadv:
0
->
1

add net fe80::: gateway ::1
add net ff02::: gateway ::1
IPv4 mapped IPv6 address support=NO
Starting devd.
Configuring keyboard:
keymap
.
Starting ums0 moused
.
DHCPREQUEST on em0 to 255.255.255.255 port 67

DHCPACK from 192.168.7.10

bound to 192.168.7.142 -- renewal in 302400 seconds.


Creating and/or trimming log files
.
Starting syslogd.
ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib
32-bit compatibility ldconfig path:
NFS access cache time=60
Clearing /tmp (X related).
Updating motd:
.
Configuring syscons:
keymap
blanktime
.
Starting sshd.
Starting cron.
Starting background file system checks in 60 seconds.
 
Intel unterstützt nicht voll amd64 und bei gewissen Sachen wie Treiber werden nur 32bit addressiert als Beispiel und es gibt da an gewissen Ecken kleine Einbußen zum Orginal.

CPU und Board unterstützen Intel64
Du weißt ja, nur Orginal ist echt.

Gruß
 
Zuletzt bearbeitet:
@Kamikaze: Wenn ich mich bei der KDE anmelde, dann dauert es ca. 1 Minute(!) Bis der Desktop erscheint.

Ich habe während des starten systat -iostat laufen lassen, und habe 100% Auslastung im user Bereich gesehen.

systemmonitor unter KDE kann ich immer 2 Prozesse mit 50% im kdeinit sehen. Die Programme starten immer mit 30-45 Sekunden Verzögerung. :-(

Was läuft hier falsch?

@Flex6: Ich glaube auch, dass nur das Original lauft. Ich habe nur hier den Rechner in der Firma und der ist einfach so konfiguriert. Blödes Glumpp. ;-)

r_friemer
 
Das Thema "amd64 auf Intel" ist überbewertet. Es stimmt, dass bei sehr frühen Intel-Prozessoren aus der Netburst-Ära einige CPU-Instruktionen aus dem amd64-Befehlssatz fehlten. Später hatten die Core2-Prozessoren unter amd64 einige Optimierungen nicht, so konnte die "Macro-Op Fusion" im Longmode nicht arbeiten. Beides resultierte daraus, dass die 64-Bit-Unterstützung nachträglich in ein bestehendes CPU-Design eingefügt werden musste, da Intel seine Fische davonschwimmen sah. Wirklich böse Auswirkungen hat in der Praxis beides aber nicht. Die fehlenden Instruktionen wurden lange vermieden und die Macro-Op Fusion kann man allenfalls in synthetischen Benchmarks rausmessen. Bei neueren Intel-Prozessoren - beginnend ab Nehalem-Generation - ist Intel64 allerdings eine vollständige und uneingeschränkte Implementierung von amd64. Leider Gottes ist sie durch einige schöne Decoder-Magie sogar performanter als AMDs derzeitige, was sich in den nächsten Wochen aber hoffentlich wieder in Richtung Gleichstand korrigieren wird. :)
 
Du vergisst die 3GB Speichergrenze, Yamagi.

Was noch nett ist, ist dass der ganze nichtportable i386-Müll auf der amd64-Plattform nicht existiert. Das führt dazu, dass man nicht einmal auf die Idee kommt, es zu installieren. Implizit ist im Punkt Sicherheit amd64 also auch besser. Wer das nämlich mit dem "long int" auf die Reihe gekriegt hat, der hat schon etwas mehr verstanden als der Durchschnitt der kommerziellen Programmierer.
 
Wieso die 3GB-Grenze? Die zeigt sich ja nur, wenn ich ein i386-System auf der CPU nutze, ich sprach aber von einem amd64-System. Das kann natürlich auch auf Intel-Plattformen theoretisch 2^64 Byte Speicher adressieren.
 
jein.
deine cpu kann 2^64 byte adressieren.
aber die restliche hardware nicht.
die haben intern unter umstaenden nur 32 bit pointer.

das wird dann bei dma-prozessen haarig. weswegen openbsd auch immer noch in der standardinstallation das bigmem ausgeschaltet hat.
 
@Yamagi: ich habe ja nur gemeint, dass falls man mehr als 3GB hat, möchte man gerne amd64 haben. Dein Post klang so als ob es für amd64 keinen guten Grund gäbe.
 
Achso. Das meinte ich nicht. Ich würde immer amd64 nehmen, wenn die CPU es kann. :)
 
Ich will euch ja nicht stören, aber ...

... Lese ich das richtig, dass ich noch die 32Bit Umgebung einbinden sollte, um eine bessere Kompatibilität zu erreichen?

r_friemer
 
Mit "kaputt" meine ich hoffnungslos kaputte Applikationen aus den Ports, zum Beispiel wine. amd64 ist schon OK für Dein Szenario, finde ich.
 
Mein Problem ist, dass ich gerade eine Standard Installation gemacht und dann xorg und kfe4 über pkg_add -r auf dem Rechner installiert habe.

Sind diese Packages nicht in 64-bit kompiliert?

r_friemer
 
Nein, FreeBSD/amd64 installiert immer entsprechende Pakete. Das wird also schon richtig sein. Wenn du ganz sicher gehen willst, rufst du einfach mal file(1) auf einem Programm auf, es sagt es dir dann eindeutig:
Code:
yamagi@saya:pts/13 ~: file /usr/local/bin/vim                        [9:48:08]
/usr/local/bin/vim: ELF 64-bit LSB executable, x86-64, version 1 (FreeBSD), dynamically linked (uses shared libs), for FreeBSD 8.2, stripped
Das Problem sind aber wahrscheinlich deine beiden amoklaufenden KDE-Prozesse. Leider habe ich von KDE so gut wie keine Ahnung, weshalb ich der falsche Ansprechpartner bin. Sollte sich hier aber niemand sonst melden, könntest du einmal ein dezentes "rm -Rf ~/.kde ~/.qt" machen und ganz von vorn beginnen. Eine neue Konfiguration kann gern mal Wunder wirken.
 
Danke Yamagi. Das klingt gut.

Ich werde das ausprobieren. Ich vermute, dass kompilieren besser ist als package installieren, aber das muss ich heute nacht einmal testen.

Ich melde mich morgen wieder.

Grüße

r_friemer
 
Ich wollte nun kurz einen Zwischenbericht abgeben.
Ich habe den Kernel einmal neu kompiliert und anschließend die 32Bit Umgebung, wie sie auch für VirtualBox benötigt wird, kompiliert.

Leider hat dies immer noch keine Verbesserung gebracht. :-(

Was mir aber mit mit systat -vmstat aufgefallen ist, bei CPU0 und CPU1 sind im 2000 Interrupts. Ist das normal? Woher kommen diese?

r_friemer
 
Zurück
Oben